User manual SMEG CWC631DHE

[. . . ] PROFESSIONAL DISHWASHER CW 620/630 CONTENTS 1 PRECAUTIONS FOR SAFETY AND USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 INSTALLATION AND POSITIONING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4 INSTRUCTIONS FOR TECHNICAL STAFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4. 1 Plumbing hookup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4. 2 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 FIRST STARTUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 6 SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 6. 1 Dishwasher parameter modification procedure: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This parameter cannot be modified or reset unless the software is reprogrammed. 15 CW 620/630 Steam extraction system operating time display and setting This submenu and the relative functions can only be accessed with the aid of a password available on SmegTech and only by technical staff. 6. 2 Quit " SETUP " menu Wait more than 10 seconds without pressing any button and the appliance quits this menu automatically, or press the on/off button to exit. Caution: the tank and boiler temperatures shown on the display may be different from the actual temperatures by a few degrees, especially in transient phases (just after the FILL is completed, just after the end of the cycle, etc. ) due to the inertia of the measurement probe. 6. 3 Rinsing temperature setup Modify the value of the parameter by pressing . 16 CW 620/630 6. 4 Washing temperature setup Modify the value of the parameter by pressing . 6. 5 Rinse aid dispensing setup RINSE AID Modify the value of the Delivery time Delivery parameter by pressing (s) quantity (c. c. ) . 0 * default value (factory preset) 6 12 18 24 30* 36 42 0, 0 0. 6 1. 2 1. 8 2. 4 3. 0 3. 6 4. 2 6. 6 Adjusting detergent dispensing (optional if installed) DETERGENT Modify the value of the Delivery time Delivery parameter by pressing (s) quantity (c. c. ) . 0 0. 0 4 * default value (factory preset) 8 12* 16 20 24 17 1. 4 2. 8 4. 3 6. 7 7. 1 8. 5 11. 7 13. 3 15. 0 30 36 42 CW 620/630 6. 7 Autostart function Modify the parameter (ON/OFF) by pressing . Set at "off" for cycle start after confirmation with the start button 6. 8 Regeneration frequency setup (models with softener) (Default value: H03; modify the parameter to suit the mains water hardness. It is subsequently sufficient simply to fill up with regenerating salt when necessary. Hardness (°dH German Modify the degrees) Regeneration value of the off parameter 8. 5 by pressing 11 . 17 22. 5 28 Hardness (°dF French degrees) Regeneration off Setting level H00 H01 H02 H03 H04 H05 Important: 15 20 30 40 50 60 During normal operation, the dishwasher will perform a number of washing cycles while regeneration is in 33. 5 H06 progress. During this time (56 cycles) the intake water will not be treated, but this will not affect the washing quality. With values over 60°f an external water treatment device must be used and the regeneration frequency must be set on H00. 18 CW 620/630 6. 9 tStP (minimum rinsing temperature) function Modify the parameter (ON/OFF) by pressing . Set at "on" for minimum rinsing temperature as set; set at "off" for rinsing regardless of boiler temperature. If the parameter is set as "off" and hot intake water is not used, the minimum rinsing temperature might be a few degrees lower than the setting. If the thermostop device is set "off" the rinsing T° are no longer monitored and the user is responsible for ensuring that the minimum correct T° are maintained for the tank and boiler. It is particularly important to check the intake water temperature. Also refer to the insufficient washing/drying /foam in tank point of the "troubleshooting" section : restore T Stop ON and/or connect the appliance to a hot water supply 6. 10Rinse aid pump (display and if required reset during maintenance) To reset, press for 3 seconds. 6. 11Detergent pump (display and if required reset during maintenance) To reset, press for 3 seconds. [. . . ] Check that the filter of the hose inserted in the rinse aid tank is not fouled. Check container of rinse aid and whether it is suitable for the type of mains water. Check boiler temperature setting If the problem persists, contact the aftersales service. Inappropriate cycle set Spray arm nozzles fouled Limescale in boiler INADEQUATE RINSING Rinse aid unsuitable or not being delivered correctly. [. . . ]