User manual SMEG JLRCSS104

[. . . ] JLRCSS104 JLRCBK105 Range cooker Instruction manual Important safety information Thank you for purchasing this appliance. This manual is an integral part of the appliance and therefore must be kept in its entirety and in an accessible place for the whole working life of the cooker. Please read the instructions and warnings carefully before use to ensure safe and satisfactory operation of this product. Installation must be carried out by qualified personnel in accordance with the regulations in force. [. . . ] In this case the programmer will calculate the start time to be at 19:10 and will start and end automatically. 1 Press the "cooking period" key, the display lights up, showing 00:00. The `A' simbol will appear on the display, and the current clock time will be shown. Press the "end time" key, the display lights up, showing the current time. The `A' simbol 15 Erase of set data Once the programmer has been set, press the key of the function to be cancelled. Time cancellation will be considered as end of cooking time by the programmer. Adjusting alarm volume The acoustic alarm has three different settings. These can be operated, while the alarm is sounding , by pressing the key. Use of the hob Caution!Before lighting the hob burners check that the flame caps are in the correct position and that their burner caps are in place, making sure that the holes A in the flame caps correspond to the spark plugs and thermocouples. To prevent deterioration of the hob the appliance is equipped with a raised pan stand to be placed underneath pans more than 26 cm in diameter. The supplied reduction rest is used also for small pans. Lighting of the hob burners This optional grid is for use with "woks" (Chinese pans). The drawing next to each knob shows the corresponding burner. Simply press and turn the knob anticlockwise to the minimum flame symbol , until the flame is lit. Hold the knob down for a few seconds to allow the thermocouples to heat up. The burner may go out when the knob is released: this is because the thermocouple has not been sufficiently heated. (cm) 12 16 18 18 14 24 26 26 In the event of a power failure the burners can be lit with a match or gas lighter. The flame failure devices will continue to function normally. 1 Auxiliary 2 Semi rapid 3 Rapid 4 Triple crown Practical advice for using the hob burners For better use of the burners and lower gas consumption, use covered vessel that are proportional in size to the burner to prevent the flame from licking the sides. When water reaches the boiling point, lower the flame so that it doesn't overflow. To avoid burns or damage to the hob, all vessels or griddle plates must be placed within the perimeter of the hob. When using fats or oils, be extremely careful that they don't overheat and catch fire. If the flame accidentally goes out, turn off the control knob and wait at least 1 minute before trying to re-light the burner. When using for the first time, it is advisable to heat up the cooking hob to its maximum temperature for enough time so as to burn off any possible oily manufacturing residues, the smell of which could otherwise be absorbed by the food. Diameter of the vessels to be used on each burner 17 Cleaning your appliance Warning!Before any intervention, disconnect the power supply of the device Caution!Never use a steam jet to clean the appliance. Cleaning the oven For best oven upkeep clean regularly after having allowed to cool. Take out all removable parts. Cleaning stainless steel To keep stainless steel in good condition, it must be cleaned regularly when you are done using the cooker, after it has cooled. · Clean the oven grill with hot water and non-abrasive detergent. [. . . ] Screw the assembly to the moveable connector A of the appliance, placing the seal C between them. When making the connection, make sure that no stress of any kind is applied to the cooker and that the hose does not touch any sharp edges. If connecting to LPG the bayonet hose must have red bands on it. Replacement of nozzles on the hob To change the nozzles, proceed as described below: 1 Extract the grids and remove all the caps and flame-spreader crowns; 2 Unscrew the burner nozzles with a 7 mm socket wrench; 3 Replace the nozzles according to the type of gas to be used 4 Replace the burners in the correct position. Adaptation to different types of gas Warning!Before performing any cleaning or maintenance work, disconnect the appliance from the mains. [. . . ]