User manual SMEG KDD90VXE

[. . . ] When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0, 04 mbar to prevent fumes being drawn back into the room by the cooker hood. • In the event of damage to the power cable, it must be replaced by the manufacturer or by the technical service department, in order to prevent any risks. • If the instructions for installation for the gas hob specify a greater distance specified above, this has to be taken into account. [. . . ] • Fix the Hood Canopy with the 2 screws 12c provided. Warning: If the cooker top is made from a material that does not allow the screws 12c to be inserted, use a small amount of silicone to glue the Brackets 7. 2 to the top and allow it to dry completely before proceeding with installation. EN 2 25 Fixing the Lower Brackets • Screw the brackets 7. 1 to the front of the Hood Canopy using the screws 12a provided. • Before tightening the Brackets completely, make all the adjustments to allow them to rest on the lower base of the worktop to avoid deformation of the upper brackets 7. 2 as shown in the figure. 12a 7. 1 12a 7. 1 • With the aid of a spirit level, set the Hood Canopy level vertically and fix it to the Lower Surface using 2 screws 12c provided. 12c • Tighten the screws 12a completely. EN 2 26 Fixing the Squaring Brackets • Screw the brackets 7. 3 to the Hood Canopy using the screws 12b provided, without tightening completely. • Using the screws 12c provided, fasten the other part of the brackets 7. 3 either to the side walls of the unit or to the lower part of the cooker top. 7. 3 12b 7. 3 12b 12c • Tighten the screws 12c and 12b completely. EN 2 27 Fixing the Motor Unit • Installation of the Motor Unit (1) at the front or rear must be decided according to the position of the Kitchen unit, making sure that the plug is properly positioned. • Subsequently, according to where the air outlet opening has been created on the unit, the Motor Unit can be turned by 90° at a time so as to allow the air to come out on all 4 sides in correspondence with the opening in Unit (2). • Remove the Motor Unit from the support by unfastening the 2 screws (A). • Connect the connector from the Hood Canopy to the Motor Unit connection. • Replace the Motor Unit in the support using the 2 screws removed as described above. A • Screw the Motor Unit to the Hood Canopy using the screws 12a and 12b provided as shown in the figure. EN 2 28 Fixing the Electric Unit • Connect the Electric cables that come out of the lower right hand part of the Hood Canopy to the Connectors on the Electric unit. • Each cable connector has a corresponding connector on the Electric Unit, so take care not to make mistakes when connecting up. • Fix the Electric Unit to the Hood Canopy using the screws 12a provided. • The position indicated in the figure is only an option, as if necessary it may also be fitted on the left of the Hood Canopy or even left free on the base of the unit if there are no structural or safety problems involved. Warning. . : Do not install the product in such a way that the wiring box is in contact with the floor. EN 2 29 Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ø 150 or 120 mm, the choice of which is left to the installer. • To install a ø 120 mm air exhaust connection, insert the reducer flange 9 on the hood body outlet. • Fix the pipe in position using sufficient pipe clamps (not supplied). • Remove possible charcoal filters. ø 150 9 ø 120 AIR OUTLET – RECIRCULATION VERSION • Connect the Flange to the air outlet opening using a rigid or flexible pipe of ø120 or 150 mm. • To connect using a ø120 mm pipe, insert the reduction Flange 9 onto the Hood canopy outlet. • Fix the directional Grid 8 on the outlet, using 2 screws 12e (2. 9 x 9. 5) provided. • Make sure that the activated charcoal filters are present (see paragraph on Activated Charcoal Filter Maintenance). ELECTRICAL CONNECTION • Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. . APPLIANCE IN LET EN 3 30 Fitting the Front element • Lift the mobile hood canopy (see paragraph on Use) by just a few centimetres. • To stop movement, simply press down on the mobile canopy as it lifts up. Warning: Never block the sliding door when it is opening or closing, except during the operations required to fit the frame. • Take the front Frame and insert it from above, making sure that its tabs insert into the slots provided on the Hood and sliding it to the left. [. . . ] Activating the alarm signal • In Recirculation Version Hoods, the Filter Saturation Alarm must be activated on installation or at a later date. • Press and hold button E for 2 seconds: • C flashes twice – Activated Charcoal Filter saturation alarm ACTIVATED. • C flashes once – Activated Charcoal Filter saturation alarm DEACTIVATED. [. . . ]