User manual SMEG P755AXA-1

[. . . ] INSTRUCTIONS FOR USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 ENVIRONMENTAL RESPONSIBILITY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 DESCRIPTION OF CONTROLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To position the racks correctly, align the reference notches (A) with the cavities (B) on the hob. After positioning, check that the rack feet are all resting on the same level. Make sure that the racks are simply centred on their respective burners, without forcing the burners to be raised or tilted. If they are, repeat the positioning procedure. INCORRECT INCORRECT CORRECT 11 Instructions for the user 5. 2 Lighting the burners using a safety device , until it The appliance is equipped with electronic ignition. Simply press the knob and simultaneously turn it anticlockwise to the minimum flame symbol lights. Hold down the knob for about 2 seconds to keep the flame lit and to activate the safety device. If this happens, repeat the procedure, holding the knob down for longer. If the burners should go out accidentally, after about 20 seconds a safety device will be tripped, cutting off the gas supply, even if the gas tap is open. 5. 3 Practical tips for using the burners For better burner performance and minimum gas consumption, pans with flat, even bases and with lids should be used, and their size should be in proportion to the burner (see “5. 4 Pan diameters”). During cooking, in order to avoid burns or damage to the hob top, all pans or griddles must be positioned inside the outer edge of the hob and at a minimum distance of 5-7 cm must be maintained from the knobs. If the burner flame accidentally goes out, turn off the control knob and wait at least 1 minute before trying to re-light the burner. 12 Instructions for the user 5. 4 Pan diameters BURNERS 1 2. Ø (in cm) 7-18 10-24 18-24 20-26 13 Instructions for the user 6. CLEANING AND MAINTENANCE Before performing any operations requiring access to powered parts, disconnect the appliance from the power supply. 6. 1 Cleaning the hob To keep the hob in good condition it should be cleaned regularly after use. Let it cool first. 6. 1. 1 Ordinary daily cleaning To clean and preserve the stainless steel surfaces, always use only specific products that do not contain abrasives or chlorine-based acids. How to use: pour the product onto a damp cloth and wipe the surface, rinse thoroughly and dry with a soft cloth or chamois leather. 6. 1. 2 Food stains or residues Do not use metallic sponges or sharp scrapers: they will damage the surface. Use ordinary non-abrasive products for steel, together with antiscratch sponges and wooden or plastic utensils if necessary. Rinse thoroughly and dry with a soft cloth or chamois leather. 14 Instructions for the user 6. 2 Cleaning the components 6. 2. 1 Knobs The knobs should be cleaned with a soft cloth dampened with lukewarm water, then dried carefully. Do not use aggressive products containing alcohol or products for cleaning steel and glass when cleaning the knobs, as these products could cause permanent damage. 6. 2. 2 Racks Remove the racks and clean them with lukewarm water and nonabrasive detergent, making sure to remove any encrustations. Wash them with lukewarm water and non-abrasive detergent, making sure to remove any encrustations. To remove burned on food residue, use Puliforno with a scourer sponge. The dimensions given in the following drawing refer from the hole to the inside of the seal. The figure to the side shows the exact holes to be used to correctly attach the hob to the work surface with brackets. IMPORTANT: If installing the hob over an oven, ensure that the latter is equipped with a cooling fan. 17 Instructions for the installer 7. 2 Clearances above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measurement A) Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. [. . . ] Once all burners have been tested individually, turn all burners on together. To check the operating pressure of the appliance it is recommended at least 2 large size burners are used. The regulator supplied must be fitted to the ½ BSP thread at the rear of the appliance. Installation with flexible hose must be carried out so that the length of the piping does not exceed 2 metres when fully extended; make sure that the hoses do not come into contact with moving parts and that they are not crushed in any way. 21 Instructions for the installer 9. 2 Room ventilation The room containing the appliance should have a permanent air supply in accordance with the standards in force. [. . . ]