User manual SMEG PW4060

[. . . ] PW4060 PUNCH WASHER USER MANUAL READ THE USER MANUAL WITH CARE This manual is an integral part of the appliance. Take good care of it and keep it to hand throughout the appliance’s life cycle. This manual and all the information it contains must be read carefully before using the appliance. Failure to read, any misunderstanding or incorrect interpretation of the instructions provided in this manual may lead to misuse of the device, put the operator at risk and impair the device’s performance. [. . . ] Display and Display shows Setting in ml/litre, the default value of this parameter is Modification 3ml/litre. (Max setting 20ml/litre) Increase/decrease the setting with the Select buttons. Modification -3 NB: consider the table of dispensing rates for this pump Water hardness Set the hardness in °f, in steps of 5. Attention: Make sure that the value corresponds to the actual hardness of the water supply. Automatic opening at end of cycle The default setting on PW appliances is “On”, but automatic door opening can be disabled by changing the parameter to “Off”. If the option is enabled, the device door is opened automatically at the end of the cycle. Printer language English by default, the language can be chosen from the various options available German French Spanish Italian English dE Fr ES It En Demineralised water The use of demineralised water can be activated or deactivated depending on whether or not the relative connection has been made (Activated: dn, Deactivated: --) Filter hours left (only installed on PW4060) The parameter indicates the number of fan operating hours left before filter replacement. Display and Modification Display and Modification -4 Display and Modification Display and Modification -5 Display and Modification Display and Modification -6 -7 Display and Modification Display and Modification Display Only Display Only -8 User Manual PW4060 Series Page 39 - 78 Set PARAMETER DESCRIPTION Cycles left before service Indicates, to the nearest ten, the number of cycles left before the routine service (e. g. “-9. 20” on the display indicates that there are 200 cycles left before the service alert). Power Supply The parameter indicates whether the connection is: - single-phase: parameter setting “1” - three-phase: parameter setting “3” N. B. : the value “3” refers to both 400V 3N~ / 50 Hz and 230V 3~ / 50Hz connections. Warning: this parameter is only used for the correct setting of times remaining. Memory Data Overwriting - Overwriting enabled: parameter setting “1” - Overwriting disabled: parameter setting “0” The parameter refers to whether or not the device’s internal memory, which keeps a record of all the cycles performed and the alarms which have occurred, can be overwritten. WARNING If overwriting is disabled, alarm AF:91 is triggered once the memory is full. In this case the appliance will not perform any more cycles until the data from the memory are downloaded; this can only be done using the TRACELOG software. Use of powder dispenser (Parameter introduced from Main Firmware version 1. 11. 0. 33). This parameter only appears on some models, which are fitted with the powder detergent dispenser on the door liner. It may assume the following values: “-C:dd”, means that the powder dispenser (DD) is fitted and activated; the dispending rate set using parameter P1: “Set -1” is not considered. Detergent is dispensed at the rate set in parameter "Set -1”. If “-d: 0” the superuser is able to modify the dosages If “-d: 1” the superuser is not able to modify the dosages but can display them. This Parameter can only be modified by the authorised engineer. POSSIBLE SUPERUSER ACTION With set With set parameter parameter “-d=0” “-d=1” Display Only Display Only -9 Display Only Display Only -A Display and Modification Display and Modification -b Display Only Display Only -C Display Only Display Only -d User Manual PW4060 Series Page 40 - 78 Set PARAMETER DESCRIPTION Parameter for setting presence or absence of the WDLANE accessory. -E Sets the serial port communication speed “-E: Pr” = 9600 bps (for Printer connection) “-E: Ln” = 11500 bps (for connection to WD-LANE - LAN accessory). Test cycle Display Only (Parameter introduced from Main Firmware version 1. 11. 0. 33). [. . . ] SMEG declines all responsibility for any damage or injury caused by incorrect installation of the pump by unauthorised technical staff. fig. 50 – Unpressurised tank, height above appliance installation surface. User Manual PW4060 Series Page 73 - 78 14. 2 WATER DRAIN Appliance drain hoses: Rubber terminal for dia. WATER DRAIN CONNECTION The appliance is equipped with one or more drain hoses, depending on the model. The drain hoses are indicated as: - d - appliance drain hose – d (drain) - cd - steam condenser drain hose – cd (condenser drain) The following table and diagram summarise the situation. fig. [. . . ]