User manual SMEG SC845MPO9

[. . . ] Recommendations are given for the correct use of the baskets, spray arms, containers, filters, washing programs, and for operating the controls. Following the cleaning instructions provided here will keep your dishwasher's performance at peak levels in the long term. This user-friendly manual will provide answers to all your questions about use of the dishwasher. INSTALLATION INSTRUCTIONS: these are intended for the qualified technician who must carry out the installation, hook-up and testing of the appliance. USER INSTRUCTIONS: these consist of recommendations for using the appliance, a description of its controls and of the correct cleaning and maintenance procedures. 1 Safety instructions 1. [. . . ] At the end of the delay set, the option light goes out and the washing cycle starts. N. B. : It is not possible to select the PROGRAM DELAY option once the cycle has begun. Chosen the delay, proceed with the program start, press the button START/PAUSE (6) for same seconds until the START/PAUSE (D) symbol start to flash. The machine will perform a dish pre-washing, and when finish, the “delay program” will enter in function as it was first set. In case you want to put to zero the “delay program” within the running program it is necessary: to press the START/PAUSE (6) button for some seconds until the START/PAUSE (D) symbol remain lid up on the display; • to press the DELAY PROGRAM (5) more times until the reset of the delay program (START/PAUSE (D) symbol shut off); • to press the START/STOP (7) button to make start the program. N. B. : It is not possible to select the “delay program” when the program have already began. • 17 User instructions OPTIONS (available in all programs except the soak program) The options are controlled by the OPTION SELECTION button (3). Press the button to access the procedure, confirmed by flashing of one of the OPTIONS lights (E). N. B. : The PROGRAM DELAY light only comes on when the specific PROGRAM DELAY button (5) is pressed. Press the SELECT OPTIONS button (3) again to display the next option. To confirm an option, press the CONFIRM OPTION button (4) (the light stops flashing and remains on). This operation can be carried out for one or all of the options available. The dishwasher is equipped with an automatic softening system which uses a special regenerating salt to reduce the hardness of the water. The dishwasher is factory set for water hardness level 3 (average hardness). SALT When using water of medium hardness, the regenerating salt container should be refilled after approximately 20 washing cycles. After removing the lower basket, unscrew the salt container cap by turning it anticlockwise and pour in the salt using the funnel supplied with the dishwasher. Before replacing the cap, remove any salt residues from around the opening. • • When using the dishwasher for the first time, in addition to the salt it is also necessary to add one litre of water to the container. Each time the salt container is refilled, make sure that the cap is securely closed. The mixture of water and detergent must never penetrate the salt container, as this would compromise the operation of the regeneration system. Only use regenerating salt specially formulated for domestic dishwashers. If using salt tablets, do not fill the container completely. • 21 User instructions • • Do not use table salt as it contains insoluble substances which, over time, may damage the water softening system. When necessary, refill the regenerating salt container before starting the washing program. In this way, the excess saline solution will be immediately removed by the water; the prolonged presence of salt water inside the tank may lead to corrosion. Be careful not to confuse the salt and detergent packages; adding detergent to the salt container will damage the water softening system. ADDITIONAL FUNCTIONS (Customizing the consumer parameters) (available in all programs except the soak program) The electronic control system allows personalizing the machine use directly through a programming procedure not directly accessible that allows: regulate water hardness level. To access the programming environment, the appliance must be turned on with the door open. [. . . ] CLEANING THE WATER INTAKE FILTER The water intake filter A located at the outlet of the water supply tap needs to be cleaned periodically. After having closed the water supply tap, unscrew the end of the water intake hose, remove the filter A and clean it delicately under running water. Reassemble filter A in its seat and carefully screw the water intake hose back into position. CLEANING THE SPRAY ARMS The spray arms can be easily removed for periodic cleaning of the nozzles, to prevent possible clogging. [. . . ]