User manual SMEG SCP490X-8

[. . . ] INSTRUCTIONS FOR USE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAFETY PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GET TO KNOW YOUR OVEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AVAILABLE ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] It is not possible to set the cooking start time only, without setting the cooking duration. Turning PT1 to the right increases the time, allowing the cooking start time to be set. A few seconds after the desired duration is set, and will stop flashing and remain constantly on, and the oven will start to wait for the starting time set. At the end, the word STOP will appear on DSP1, cooking will stop and a buzzer will sound; press PT1 once to deactivate it. The oven will restart normal operation with the cooking settings selected previously. To switch the oven off completely, PT2 must be turned to 0. 66 Instructions for the user Modifying the set data Once programmed cooking has started, its duration can be changed. When and are steady and cooking is in progress, or the oven is in starts flashing and standby waiting for cooking to start, press PT1 once. Press PT1 again; goes out, starts to flash, and the cooking start time will be displayed on DSP1. A few seconds after the last change, and will appear (in steady mode) on DSP1 and programmed cooking will restart with the new settings. Once the desired function has been selected, the oven will begin cooking at the preset temperature. Cooking is preceded by a pre-heating phase (common to all functions) which allows the oven to reach the cooking temperature more quickly. This phase is indicated by pre-heating phase, flashing on the display (DSP1). At the end of the will remain constantly on to indicate that the food can be placed inside the oven. 7. 7. 4 Changing the preset temperature The preset temperature for each function can be changed to suit the user's requirements. At any time while cooking is in progress, turn PT1 in either direction to increase or decrease the cooking temperature by 5 degrees at a time. PT1 can also be held in the left or right position to increase or decrease the setting more quickly. 67 Instructions for the user 7. 8 Secondary menu (pyrolytic models) The secondary menu appears on first use, after a power failure or by holding PT1 down for 3 seconds with the oven set to OFF (see "7. 4 Operating modes (pyrolytic models)"). The secondary menu enables the user to: Set the time shown on the display (DSP1). 1 P1: OFF / ON Activate or deactivate the child safety lock ( ); this function, after 2 minutes of operation without any actions by the user, locks all the functions and knobs; it is identified by the appearance of on DSP1. To temporarily deactivate locking and modify a cooking programme or select a different function, keep PT1 pressed down until disappears from DSP1. At this point you can make the desired changes, and 2 minutes after the last setting, the lock will be reactivated. To permanently deactivate the lock, you have to enter the secondary menu and deactivate it as described in this paragraph. 2 P2: OFF / ON Activate or deactivate the Show Room function; this function disables all the heating elements so that only the control panel works (to use the oven normally, set P2:OFF). 3 P3: OFF / ON Activate or deactivate the function that allows a maximum consumption of 2300 W. When the child safety lock is activated (P1:ON), if a knob is moved , "bLOC" is displayed on DSP1 for 2 seconds. [. . . ] The glass panels of the door can be completely removed by following the instructions provided below. Warning: before removing the glass panels, make sure that at least one of the door's hinges has been locked in the open position as described in "10. 2 Removing the door". This operation may have to be repeated during the glass removal process if the door is accidentally freed. 84 Instructions for the installer Removing the internal glass panel: · Remove the internal glass panel by pulling the rear part gently upwards, following the movement indicated by the arrows (1). · Doing this detaches the 4 pins attached to the glass from their slots in the oven door. [. . . ]