User manual SMEG SD20

[. . . ] THE ENVIRONMENT - DISPOSAL INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USER RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SUGGESTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] IT IS ADVISABLE TO FILL THE TANK ONLY AFTER THE HOME GARDEN HAS BEEN POSITIONED. 33 First use 6. FIRST USE The inside of the appliance should be cleaned to remove all manufacturing residues. The following are the only procedures required to start up the Home Garden when using it for the first time: 1 switch on the Home Garden by pressing the button on the remote control (see Section "9. 2 Standby key"); 2 select the program depending on the type of plants you wish to grow (see paragraph "10. 3 Selecting the programme"); 3 set the time (see paragraph "9. 6 Clock display/setting key"); 4 fill the tank (see paragraph "11. 1 Filling the tank"); If the Home Garden has been switched off for less than 3 months, it will store both the time and the last program selected. 34 Getting to know your appliance 7. GETTING TO KNOW YOUR APPLIANCE HUMIDIFIER WATER TANK CONTROL PANEL SLIDING TRAYS PLANT POTS VAPOUR DELIVERY TUBE LED LAMP HUMIDITY AND INTERNAL TEMPERATURE SENSOR TANK FILLER CAP HEATING PLATES (FIG. 8) EXTERNAL LIGHT SENSOR INTERNAL CLOCK SETTING/DISPLAY SYMBOL HUMIDITY SUPPLY/EMPTY TANK SYMBOL INTERNAL TEMPERATURE/TIME DISPLAY STANDBY SYMBOL INTERNAL AIR HUMIDITY PERCENTAGE/MINUTES DISPLAY REMOTE CONTROL LOCK SYMBOL LED LAMP MAXIMUM LIGHT SYMBOL CUTTINGS FUNCTION SYMBOL REMOTE CONTROL INFRARED SENSOR 8. 1 External light sensor This sensor detects the environmental light level also controlling the lamp on or off during lighting period set with the program. 8. 2 Internal clock setting/display symbol This symbol indicates that the key on the remote control has been pressed to show the current time on the displays. For instructions for setting the time, see "9. 6 Clock display/setting key" 8. 3 Humidity supply/empty tank symbol This symbol lights up whenever the key on the remote control is pressed. It flashes when the water tank level goes into reserve and the humidifier is no longer able to deliver the required vapour. For filling the water tank, read paragraph "11. 1 Filling the tank". In normal operating conditions, the tank will ensure correct humidification for 25-30 days. This value is approximate and will depend on the climatic conditions and program selected. 36 Control panel 8. 4 Internal temperature/time display During normal operation, this displays the Home Garden’s internal temperature. When first switched on, after a power shutdown or when the key is pressed, the display shows the time for setting. For instructions for setting the time, see "9. 6 Clock display/setting key" The Home Garden does not have a cooling function. It follows that the internal temperature will never be lower than the external temperature. 8. 5 Standby symbol When this is the only symbol lit up on the control panel, the appliance is in standby. 8. 6 Internal air humidity percentage/minutes display During normal operation, this displays the Home Garden’s internal relative humidity (in %). When first switched on, after a power shutdown or when the key is pressed, the display shows the time for setting. For instructions for setting the time, see "9. 6 Clock display/setting key". It follows that the internal humidity will never be lower than the external humidity. 8. 7 Key lock/unlock symbol When the remote control has not been used for ten minutes consecutively, the Home Garden locks its current setting and commands are not accepted from the remote control. This is a precaution against misuse, accidental or in play, by children, who may attempt to change the settings and thus affect the growth of the plants. For instructions for deactivating the lock, see "9. 2 Standby key". 8. 8 Internal light ON symbol This symbol lights up whenever the key of the remote control is pressed, and stays on for around a minute during day time, and an hour at night. It can be switched off manually at any time by pressing the key when it is on. For instructions for the internal lighting function, see "9. 5 Internal light key". 8. 9 Cuttings function on symbol This symbol indicates that the “Cuttings” function is activated. If it is flashing, this means that the climatic conditions do not allow for activating the function. For instructions for the “Cuttings” function, see "9. 3 Cuttings function on key". 8. 10 Remote control sensor This sensor receives the signals emitted by the remote control whenever its keys are pressed and sends them to the control circuitry, which activates the corresponding components. [. . . ] It is best to fill the tank only after having positioned the Home Garden. The tank water level can be seen through the front window, under the control panel. When the level falls below a certain value, the symbol on the control panel will start flashing. When this symbol is flashing, the humidifier is not able to generate vapour and the tank must be filled as follows. [. . . ]