User manual SMEG SF390X

[. . . ] The appliance has been built to carry out the following functions: cooking and heating up food; all other uses are considered unsuitable. The manufacturer declines all responsibility for uses other than those indicated. WHERE THIS APPLIANCE IS INSTALLED IN MARINE CRAFT OR IN CARAVANS, IT SHALL NOT BE USED AS A SPACE HEATER. UNSUITABLE IN MARINE CRAFT, CARAVANS OR MOBILE HOMES, UNLESS EACH BURNER IS FITTED WITH A FLAME SAFEGUARD If the appliance is installed on caravans or boats, it must not be used to heat rooms. Do not use this appliance for heating rooms. Before the appliance is put into operation, all protective films must be removed. DO NOT USE STEEL SPONGES AND SHARP SCRAPERS AS THEY WILL DAMAGE THE SURFACE. USE NORMAL NON-ABRASIVE PRODUCTS, INCLUDING WOODEN OR PLASTIC UTENSILS IF NECESSARY. [. . . ] Before disposing of your appliance it is important to remove doors and leave shelves in the same position as for use, to ensure that children cannot accidentally become trapped inside during play. It is also necessary to cut the connecting cable to the power grid, removing it along with the plug. 8 Instructions for the user 4. USING THE HOB 4. 1 Lighting the hob burners Before lighting the hob burners, check that the flame-spreader crowns are correctly in place with their respective burner caps, making sure that the holes 1 in the flame-spreaders are aligned with the plugs 3 and thermocouples 2. To prevent damage to the work top, the hob comes complete with a raised pan stand 4: This must be placed under pans with a diameter greater than those indicated in the table in point "4. 3 Cookware diameters". In any case, pans with a diameter greater than 28 cm must be used solely on the central burner. The pan stand 4 can also be used with woks. 4 1 2 3 1 2 3 The burner controlled by each knob is shown next to the knob. Simply press the knob and turn it anti-clockwise to the maximum flame symbol , until the burner lights. On valved models, once the burner is lit, keep the knob pressed for a few seconds to give the thermocouple time to heat up. The burner may go out when the knob is released: in this case, the thermocouple has not heated up sufficiently. Wait a few moments and repeat the operation, keeping the knob pressed for longer. This is not necessary on burners that are not equipped with a thermocouple. The brackets shown in the figure should be placed only after the hob has been built in. 6 73 750 1 ÷ 20 50 15 0 2 50 84 7 48 2 1 2 3 4 12 Instructions for the installer Carefully trim the surplus away from edge beyond the seal. The dimensions given in figure 2 refer from the hole to the inside of the seal. Dimensions: Gas and electrical connection location (measurements in mm). 866 267 76 73 34 38 474 511 70 3, 3 833 13 Instructions for the installer Max 150 mm Min. 20 mm Max 100 mm IMPORTANT: if the appliance is mounted on a unit, make sure that a separating shelf is installed, as shown in the figure. If the appliance is instead on an oven installed under the hob, there is no need to install a separating shelf. If installed on top of an oven, the latter must be equipped with a cooling fan. 14 Instructions for the installer 6. 2 Clearances above and around domestic appliances Extract from AS5601 REQUIREMENTS 1 Overhead clearances – (Measurement A) Range hoods and exhaust fans shall be installed in accordance with the manufacturer’s instructions. However, in no case shall the clearance between the highest part of the hob of the cooking appliance and a range hood be less than 600 mm or, for an overhead exhaust fan, 750 mm. Any other downward facing combustible surface less than 600 mm above the highest part of the hob shall be protected for the full width and depth of the cooking surface area in accordance with Clause 5. 12. 1. 2. However, in no case shall this clearance to any surface be less than 450 mm. Only use a H05V2V2-F type cable or similar withstanding a maximum temperature of 90°C. The cable must be replaced by a specialised technician who must carry out the connection to the power grid following the diagram below. L = brown N = blue = yellow/green 16 Instructions for the installer The manufacturer declines all responsibility for damage to persons or things caused by non-observance of the above prescriptions or by interference with any part of the appliance. [. . . ] After installation, the engineer must issue a certificate of compliance. 19 Instructions for the installer 7. ADAPTATION TO DIFFERENT TYPES OF GAS Before carrying out the following operations, disconnect the appliance from the power supply. In case of operation with other types of gas, the burner nozzles must be changed and the minimum flame adjusted on the gas taps. To change the nozzles, proceed as described in the following paragraphs. 7. 1 7 8 9 Replacing the hob nozzles Extract the pan stands and remove all caps and flame-spreader crowns; Unscrew the burner nozzles with a 7 mm socket spanner; Proceed with the replacement of the burner nozzles according to the gas to be used (see paragraph “7. 2 Burner and nozzle characteristics table”). [. . . ]