User manual SMEG SFP120

[. . . ] WE ADVISE CAREFUL READING OF THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE APPLIANCE. INSTALLATION MUST BE CARRIED OUT BY QUALIFIED PERSONNEL IN ACCORDANCE WITH THE REGULATIONS IN FORCE. THIS APPLIANCE IS INTENDED FOR HOUSEHOLD USE AND COMPLIES WITH THE EEC DIRECTIVES CURRENTLY IN FORCE. THE APPLIANCE HAS BEEN BUILT TO CARRY OUT THE FOLLOWING FUNCTIONS: COOKING AND HEATING FOODS; ALL OTHER USES ARE TO BE CONSIDERED IMPROPER. [. . . ] SHOULD THE APPLIANCE NOT FUNCTION, DISCONNECT IT FROM THE SUPPLY AND CALL THE NEAREST TECHNICAL ASSISTANCE CENTRE. NEVER PUT INFLAMMABLE OBJECTS IN THE OVEN: THEY COULD BE ACCIDENTALLY LIGHTED AND CAUSE FIRES. DURING USE THE APPLIANCE BECOMES VERY HOT. TAKE CARE NOT TO TOUCH THE HEATING ELEMENTS INSIDE THE OVEN. THE USE OF THIS APPLIANCE IS NOT PERMITTED TO PEOPLE (INCLUDING CHILDREN) OF REDUCED PHYSICAL AND MENTAL ABILITY, OR LACKING IN EXPERIENCE IN THE USE OF ELECTRICAL APPLIANCES, UNLESS THEY ARE SUPERVISED OR INSTRUCTED BY ADULTS OR PEOPLE RESPONSIBLE FOR THEIR SAFETY. ALWAYS CHECK THAT THE CONTROL KNOBS ARE IN THE 0 (OFF) POSITION WHEN YOU FINISH USING THE OVEN. BEFORE THE APPLIANCE IS PUT INTO OPERATION, ALL THE PROTECTIVE FILMS APPLIED ON THE OUTSIDE MUST BE REMOVED. The manufacturer declines all responsibility for damage to persons or things caused by non-observance of the above prescriptions or by interference with any part of the appliance or by the use of non-original spares. 26 Instructions for the user 4. GET TO KNOW YOUR OVEN CONTROL PANEL OVEN LIGHT ROTISSERIE MOTOR SHELF AND TRAY RUNNERS TEMPERATURE PROBE 5. Separate the various waste materials and take them to the nearest special garbage collection centre. In order to remove all manufacturing residues, it is recommended to clean the inside of the appliance. Before using the oven for the first time, pre-heat it to maximum temperature long enough to burn any manufacturing oily residues which could give the food a bad taste. 27 Instructions for the user 6. DESCRIPTION OF THE CONTROLS ON THE FRONT PANEL All the appliance's control and monitoring devices are placed together on the front panel. The symbols used are described in the table below. MINUTE MINDER KNOB The numbers correspond to minutes (maximum 55 minutes). To set the cooking time, turn the knob clockwise until it reaches the "55" position and then set the desired cooking time. GRILL COOKING FUNCTION SWITCH THERMOSTAT - Permits rapid browning of foods. For short-term cooking of small quantities, place the grid in the fourth guide from the bottom. For long-term cooking and grills, put the grid in the lowest guide in accordance with the size of the pieces. Grilling with the door open can permanently damage the oven and jeopardise safety whilst the grill is on. GRILL COOKING FUNCTION SWITCH THERMOSTAT Especially recommended for finishing the cooking for foods on the base or for cooking procedures that require heating especially in the lower part. It is recommended to insert the tray into the lowest runners. 32 Instructions for the user ROTISSERIE COOKING FUNCTION SWITCH THERMOSTAT Prepare the rotisserie rod with the food, tightening the screws A of the prongs. Remove the handle D and position the rotisserie rod so that the pulley E is still in the guides of the frame B. Insert the frame B fully until the tip of the rotisserie rod enters into the hole C on the rear wall of the oven. Place a basin F on the bottom shelf and pour a little water into it to prevent smoke from forming. 33 Instructions for the user 10. TABLE OF RECOMMENDED COOKING SETTINGS The oven must be pre-heated before every cooking operation. Cooking times, especially meat, vary according to the thickness and quality of the food and to consumer taste. [. . . ] If a fixed connection is being used fit power line with an omnipolar circuit breaker with a contact opening gap equal to or greater than 3 mm, in an easily accessible position in proximity to the oven. If a plug and socket connection is being used make sure that the plug and socket are compatible. Avoid use of adapters and shunts as these could cause overheating and risk of burns. Operation at 220-240 V~: use a three-core cable of the type H05RRF (3 x 1. 5 mm2 cable) or H05V2V2-F (3 x 1. 5 mm2 cable). [. . . ]