User manual SMEG SIM570B

[. . . ] Do not repair or replace any part of the appliance unless specifically stated in the user manual. - The power cable must be long enough for connecting the appliance, fitted in the cabinet, to the power supply. - For installation to comply with the current safety regulations, an omnipolar switch with minimum contact gap of 3mm is required. - The electrical parts must not be accessible to the user after installation. [. . . ] In order to ensure the correct operation of the product, do not obstruct the minimum required clearance between the hob and the top of the unit (min. If an undertop oven is installed, make sure the oven is equipped with a cooling system. Do not install the hob above a dishwasher or washing-machine, so that the electronic circuits do not come into contact with steam or moisture which could damage them. In the case of flush-mounted installation, call the After-Sales Service to request assembly of screws kit 4801 211 00112. To remove the hob, use a screwdriver (not provided) to prise off the perimeter clips on the underside of the appliance. EN15 ELECTRICAL CONNECTION Disconnect the appliance from the power supply. Installation must be carried out by qualified personnel who know the current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. The power cable must be long enough to allow the hob to be removed from the worktop. Make sure the voltage specified on the dataplate located on the bottom of the appliance is the same as that of the home. WARNING - - Connect to terminal Block For the electrical connection a power cord ( 5x2. 5 mm ) is present in the supply. To connect to the terminal block, follow the instuction below: L1=R BLACK        L2=S BROWN     =E YELLOW-GREEN N1=N BLUE         N2=N GREY with blue film Remove shunts from terminal block Before power cord connection remove the two shunts as per picture Connecting to the terminal block • • • Secure the power cable with the cable clamp. Remove the terminal cover (A) by unscrewing the screw and insert the cover into the hinge (B) of the terminal. Close the cover (C) and screw on the terminal with the screw removed. Connect to wall side For 220-240V 1N use the cord paired as supplied. For 380-415V 3N or 380-415V 2N, separate with the scissors the wires as showed in the image below and connect them. EN16 INSTRUCTIONS FOR USE Control Panel Description Control panel “Flexicook model” (when available) On/Off Quick access Slider Control panel lock Power management/Timer/ Lock function button Cooking zone controls and corresponding display Switching the hob ON/OFF To switch the hob on, press the button for approx. If the hob has been in use, the residual heat indicator “H” remains lit until the cooking zones have cooled down. If within 10 seconds of switching on, no function is selected, the hob switches off automatically. Switching on and adjusting cooking zones Slider operation Power indicator display Selected cooking zone indication Increase power level Cooking zone positioning Decrease power level After switching the hob on, activate the required cooking zone by pressing the corresponding circular button and place the pot on the zone. With the Slider control it is possible to select the required power level, from min. To increase the power level, slide your finger on the slider from left to right several times; to decrease it, slide in the opposite direction. Alternatively the “+” and “-” quick access buttons can be used. Deactivation of cooking zones To switch off the cooking zone, press the corresponding button for more than 3 seconds. The cooking zone switches off and, if still hot, the letter “H” appears on the zone display. EN17 Control panel lock This function locks the controls to prevent accidental activation of the hob. To activate the control panel lock, switch the hob on and press the Timer button for three seconds; an acoustic signal and a luminous indicator near the padlock symbol signal activation. The presence of water, liquid spilled from pots or any objects resting on the button below the symbol can accidentally activate or deactivate the control panel lock. Timer The timer can be used to set the cooking time for a maximum of 99 minutes (1 hour and 39 minutes) for all the cooking zones. Select the cooking zone to be used with the timer, press the timer and a beep signals the function (see figure). [. . . ] In addition, the induction hob is equipped with an internal cooling system to control the temperature of electronic parts; as a result, during operation and for several minutes after the hob has been switched off, the noise of the cooling fan will be audible. This is perfectly normal and indeed essential for proper functioning of the appliance. EN20 POWER LEVEL TABLE Power level Type of cooking Level use (indicating cooking experience and habits) Ideal for rapidly increasing the temperature of food to fast boiling in the case of water or rapidly heating cooking liquids Ideal for browning, starting to cook, frying deep frozen products, fast boiling Boost Max. power 8-9 7-8 High power 6-7 4-5 Medium power 3-4 2-3 1-2 Low power 1 OFF Zero power Fast heating Frying - boiling Browning - sautéing - boiling - Ideal for sautéing, maintaining a lively boil, cooking and grilling (for a short period of time, 5-10 minutes) grilling Browning - cooking - stewing - Ideal for sautéing, maintaining a light boil, cooking and grilling (for a medium period of time, 10-20 minutes), preheating accessories sautéing - grilling Cooking - stewing - sautéing Ideal for stewing, maintaining a gentle boil, cooking (for a long period of time). Creaming pasta grilling Cooking - simmering thickening - creaming Ideal for long-cooking recipes (rice, sauces, roasts, fish) with liquids (e. g. [. . . ]