User manual SMEG SIM571B

[. . . ] 5 mm 1 2 3 3 ENGLISH Installation Page 2 Instructions for use Page IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT This manual and the appliance itself provide important safety messages, to be read and always observed. This is the danger symbol, regarding safety, warning of potential risks to users and others. All safety messages will be preceded by the danger symbol and the following words: DANGER WARNING Indicates a hazardous situation which, if not avoided, will result in serious injury. Indicates a hazardous situation which, if not avoided, could cause serious injury. All messages relevant to safety specify the potential risk to which they refer and indicate how to reduce the risk of injury, damage and electric shocks due to incorrect use of the appliance. [. . . ] If an oven is installed beneath the hob, make sure that it is equipped with a cooling system. To remove the hob from the worktop use a screw driver (not supplied) unlocking the springs from the bottom side of the appliance. Do not install the hob above a dishwasher or washing machine, to prevent the electronic circuits from coming into contact with steam or moisture and being damaged as a result. ELECTRICAL CONNECTION WARNING Disconnect the appliance from the mains power supply. The appliance must be installed by a qualified technician who is fully aware of current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. The power supply cable must be long enough to allow the hob to be removed from the worktop. Make sure the voltage specified on the appliance rating plate is the same as that of the domestic power supply voltage. Do not use extension cables. Connecting to the terminal board For electrical connection, use an H05RR-F cable as specified in the table below. Wires 220-240 V ~ + 230-240 V ~ + 220-240 V 3 ~ + 380-415 V 3N ~ + 380-415 V 2N ~ + Number x size 3 x 4 mm2 3 X 4 mm2 (Australia only) 380-415 V 3N ~ 220-240 V ~ ( y) 220-240 V ~ (UK only) 230 V 230 V 230 V 230 V 4 x 1. 5 mm2 5 x 1. 5 mm2 4 x 1. 5 mm2 380-415 V 2N ~ 220-240 V 3 ~ (Belgium only) 380-415 V 2N ~ (Holland only) A B C 230 V 230 V 230 V 230 V 230 V 230 V Connect the yellow/green earth wire to the terminal with the symbol . Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). Insert the power supply cable into the cable clamp and connect the wires to the terminal board as indicated in the diagram next to the terminal board itself. Close the cover (C) and screw it on the terminal block with the removed screw - point (1). Select the cooking zone to be used with the timer (a dot lights up at the bottom right of the power level indicator), then set the required cooking time using the + and - keys of the timer function: the time in minutes is shown next to the cooking zone display. A few seconds after the key is pressed, the timer begins the countdown (the luminous dot of the selected cooking zone starts flashing). Once the set time has elapsed, an acoustic signal sounds and the cooking zone switches off automatically. This message remains active for 60 seconds: in this time you can add or slide pots within the Multizone area as you prefer. After 60 seconds if no pan is placed on the zone, the system stops “searching” pots on that zone, the symbol disabled. remains visible on the display to remind that the zone is i To reactivate the Multizone on both heaters, press the button . The Multizone is also able to detect when a pot is moved from one zone to the other one within the Multizone keeping the same power level of the zone where the pan originally was placed (see the example in the figure below: if the pot is moved from the front heater to the rear heater, the power level will be shown on the display corresponding to the zone where the pot is placed). It is also possible to operate the Multizone as two independent cooking zones, using the corresponding button of the single zone. Place the pot in the center of the single zone and adjust the power level with the slide touchscreen. i Important: make sure to place the pans centered on the cooking zone in the way to cover the logo placed in the center of the single cooking zone. logos. In case of big pot, oval, rectangular and elongated pans make sure to place the pans centered on the cooking zone covering both Examples of good pot placement and bad pot placement : EN18 i When the Multizone is selected, the booster and Auto-boiling functions cannot be used. If the timer is set, it will be displayed alongside the hotplate display at the top. Description of automatic functions The hob features automatic functions for each cooking zone. [. . . ] “A” appears on the display: the indicator light lights up. To deactivate the function, simply press OFF on the slide touchscreen. Melting This function maintains a permanently low temperature in the cooking zone. After positioning the pot/accessory on the chosen cooking zone, switch on the hob and select the cooking zone. Press the key: “A” appears on the display and the indicator light turns on. [. . . ]