User manual SMEG SIM581B

[. . . ] This is the danger symbol, regarding safety, warning of potential risks to users and others. All safety messages will be preceded by the danger symbol and the following words: DANGER WARNING Indicates a hazardous situation which, if not avoided, will result in serious injury. Indicates a hazardous situation which, if not avoided, could cause serious injury. All messages relevant to safety specify the potential risk to which they refer and indicate how to reduce the risk of injury, damage and electric shocks due to incorrect use of the appliance. Make sure to comply with the following: - Use protective gloves to perform all unpacking and installation operations. [. . . ] Do not install the hob above a dishwasher or washing machine, to prevent the electronic circuits from coming into contact with steam or moisture and being damaged as a result. WARNING - • • • • • • ELECTRICAL CONNECTION Disconnect the appliance from the mains power supply. The appliance must be installed by a qualified technician who is fully aware of current safety and installation regulations. The manufacturer declines all liability for injury to persons or animals and for damage to property resulting from failure to observe the regulations provided in this chapter. The power supply cable must be long enough to allow the hob to be removed from the worktop. Make sure the voltage specified on the appliance rating plate is the same as that of the domestic power supply voltage. Do not use extension cables. WARNING - - Connecting to the terminal board The hob is provided with a pentapolar cable 5x2. 5 mm2, suitable for the connection 400 V 3N ~. For electrical connection, use the cable supplied or an H05RR-F cable as specified in the table below. Conductors 220-240 V ~ + 220-240 V 3 ~ + 380-415 V 3N ~ + 380-415 V 2N ~ + Amount x size 3 x 4 mm2 4 X 1. 5 mm2 5 X 1. 5 mm2 4 X 1. 5 mm2 380-415 V 3N ~ 220-240 V ~ min 5 mm 220-240 V ~ (UK - AU) 230 V 230 V 230 V 230 V A B C 380-415 V 2N ~ 220-240 V 3 ~ (Belgium only) 380-415 V 2N ~ (NL only) 230 V 230 V 230 V 230 V Connect the yellow/green earth wire to the terminal with the symbol . Remove the terminal block cover (A), undoing the screw and inserting the cover in the terminal block hinge (B). Insert the power supply cable into the cable clamp and connect the wires to the terminal board as indicated in the diagram next to the terminal board itself. Close the cover (C) and screw it on the terminal block with the removed screw - point (1). Each time the cooktop is connected to the mains it carries out an automatic check which lasts several seconds. After 60 seconds if no pan is placed on the zone, the system stops “searching” pots on that zone, the symbol remains visible on the display to remind that the zone is disabled. To reactivate the Multizone function on both heaters, press the button . The Multizone function is also able to detect when a pot is moved from one zone to the other one within the Multizone keeping the same power level of the zone where the pan originally was placed (see the example in the figure below: if the pot is moved from the front heater to the rear heater, the power level will be shown on the display corresponding to the zone where the pot is placed). i The message “no pot” It is also possible to operate the Multizone as two independent cooking zones, using the corresponding button of the single zone. Place the pot in the center of the single zone and adjust the power level with the slide touchscreen. i Important: make sure to place the pans centered on the cooking zone. In case of big pot, oval, rectangular and elongated pans make sure to place the pans centered covering both logos on the cooking zones. 24 cm i When the Multizone function is selected, the booster and automatic functions cannot be used. If the timer is set, it will be displayed alongside the hotplate display at the top. Description of automatic functions The hob features automatic functions for each cooking zone. The symbols of the available functions are shown next to the selection key of each cooking zone. Every time an automatic function is selected, an indicator light turns on next to the symbol and the letter “A” appears in the cooking zone display. Auto-boiling Function The Auto-boiling function automatically selects the ideal power setting for bringing water to the boil and signals when boiling point is reached. After positioning the pot of water, switch on the hob and select the desired cooking zone. Press the key: “A” appears on the display and the indicator light turns on. During heating, an animation is displayed in the space next to the cooking zone. [. . . ] • Clean the hob, when it is cool, after each use in order to remove any food residues. • Sugar and foods with a high sugar content damage the glass ceramic surface and must be immediately removed. • Use a soft cloth, absorbent kitchen wipes or a specific hob cleaner (follow the Manufacturer’s instructions). TROUBLESHOOTING GUIDE • • • • • Read and follow the instructions given in the section “Instructions for use”. If, when the hob is switched on, alphanumeric codes appear on the display, consult the following table for instructions. [. . . ]