User manual SMEG SLV148ED

[. . . ] Children should be supervised to ensure that they do not play with the appliance. CHAPTER -1: BEFORE USING THE APPLIANCE (CORRECT USAGE) 7 • Use your machine only for laundries that have been specified as suitable for washing by the manufacturer. • Before operating the washing machine, remove the 4 transportation screws and rubber spacers from the back of the machine. If the screws are not removed, it may cause heavy vibration, noise and product malfunction, (voiding the guarantee). • Your machine is not covered under warranty for faults caused by any kind of external factors (pesticides, fire, etc. ). [. . . ] • Push the door of your machine until hearing the locking sound to close it. Selecting programme Select the convenient programme for your laundries on the programme table. CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (OPERATING YOUR MACHINE) 43 AUXILIARY FUNCTIONS Before starting the programme, you can optionally select an auxiliary function. • Press on the button of auxiliary function you would like to select. • If auxiliary function symbol on electronic display flashes continuously, the auxiliary function you have selected will be activated. • If auxiliary function symbol on electronic display blinks, the auxiliary function you have selected will not be activated. Reason for non-activation: The auxiliary function you want to use in the washing programme you have selected is not applicable. • Your machine has passed over the stage, during which the auxiliary function you would like to select would be implemented. • It is not compatible with an auxiliary function you have selected previously. • CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (OPERATING YOUR MACHINE) 44 HALF-LOAD DETECTION SYSTEM Your machine features a half-load detection system. In case yuo put approximately half or less amount of launderies of maximum laundry capacity in your machine, your machine will run so as to save washing time, water consumption and energy in some programmes. When the halfload function is active, the machine can complete the programme you have set in a shorter time. CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (OPERATING YOUR MACHINE) 45 TWINJET SYSTEM Detergent water in your machine will be circulated with 2 water injection mechanisms and a mixing system via twinjet system. Circulated detergent water will be injected over your laundries, which allows a better washing performance. Twinjet system will help you wash higher amount of laundries in a shorter time with a better washing performance, guaranteeing less energy and water consumption. Twinjet unit Pump unit CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING AUXILIARY FUNCTIONS 46 1- Temperature selection You can select the washing water temperature with the washing water temperature adjustment button. Whenever you select a new programme, the maximum washing water temperature is shown on the washing water temperature display. You can gradually decrease the washing water temperature between the maximum temperature and cold washing (--) by pressing washing water temperature adjustment button. When you want to start your machine, symbol will be displayed on the screen. When you take your machine into the standby mode while running, symbol will flash on the display. Main symbol explanations 12Start/Pause symbol / Door lock active/ Door lock not active 3Washing Programme remaining duration and delayed start remaining duration 4567891011Delayed Start symbol Extra rinsing and anti allergic auxiliary function symbol Pump malfunction symbol Water cut off malfunction symbol Stain level symbol Wringing speed indicator symbol Economic washing temperature indicator symbol Washing temperature indicator symbol CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (CHILD LOCK) 54 To avoid programme flow from being affected if programme buttons are pressed or programme button is turned when performing washing operation in your machine, child lock is available. Child lock will be activated in case pressed on both auxiliary functions 4 and 5 at the same time for more than 5 seconds. Y ‘’CL’’ symbol will flash on the electronic display when activated. If pressed any button while child lock is active, the “CL” symbol will blink on the electronic display. If while the child lock is engaged and any programme is running, the programme knob is switched to the CANCEL position and another programme is selected, the programme previously selected continues from where it left. To deactivate it, it will be sufficient to press on the same buttons for more than 5 seconds. When the child lock is deactivated, the “CL” symbol on the electronic display will go off. CHAPTER -5: PRELIMINARY PREPARATION FOR LAUNDERING (CANCELLING PROGRAMME) 55 If you want to cancel any programme running: 1- Switch the programme knob to “CANCEL” position. 2- Your machine will stop the washing operation and the programme will be cancelled. 3- To get rid of the water accumulated in the machine switch the programme knob to any programme. 4- Your machine will perform the necessary discharge operation and cancel the programme. [. . . ] Pursuant to discharging operation, turn off your machine and unplug it. Turn off your faucet and contact the nearest authorised service. (*) See the chapter regarding maintenance and cleaning of your machine. CHAPTER -11: AUTOMATIC FAULT WARNINGS AND WHAT TO BE DONE 79 TROUBLE CODE POSSIBLE FAULT WHAT TO DO - Water faucet may be closed. You can select a programme and run your machine after the mains water is supplied. (*) If the problem persists, unplug your machine, turn off your faucet and contact the nearest authorised service. Pump is faulty or pump filter is clogged or electrical connection of the pump is faulty. - Pump filter may be clogged. [. . . ]