User manual SMEG ST98

[. . . ] We advise you to carefully read all the instructions contained in this manual, in order to understand how to operate your dishwasher safely and correctly. The manual is divided into paragraphs, which provide a step by step description of the dishwasher functions, with clear instructions accompanied by detailed illustrations. Recommendations are given for the correct use of the baskets, spray arms, containers, filters, washing programs, and for operating the controls. Follow the recommended cleaning procedures to ensure that your dishwasher always remains in perfect working order. [. . . ] · Use the washing program that is most appropriate for each type of load. · If available, connect the dishwasher to a hot water supply up to 60°C. · When possible, disable the drying cycle and leave the door open at the end of the washing · cycle: the residual air and heat will dry the dishes perfectly. AND PROTECT THE ENVIRONMENT The phosphates contained in dishwasher detergents are harmful to the environment. To avoid using excessive amounts of detergent and to save on electricity, observe the following: · separate the more delicate items from dishes that are more resistant to aggressive detergents and high temperatures; · do not pour the detergent directly on the dishes. REMOVING THE DISHES At the end of the washing program, wait at least 20 minutes before removing the dishes, to allow them to cool down. To prevent any water droplets on the upper basket from falling on the dishes in the lower basket, it is advisable to unload the lower basket first, and then the upper basket. SLIDING FACING PANEL (for "fully integrated" models only) Some dishwashers are equipped with a FRONT DISPLAY carrying the same information as the one on the top control panel. A system which moves the facing panel allows this display to be revealed when the dishwasher door is closed; to do this follow the instructions in the "MOVING THE FACING PANEL" point. While the program is in progress, the display shows the time left before it ends (hours alternating with minutes), and the symbols described in section "3. The LUMINOUS LOGO remains off throughout the cycle and illuminates when it ends. LUMINOUS LOGO FRONT DISPLAY 32 User instructions MOVING THE FACING PANEL To lower the facing panel and reveal the FRONT DISPLAY, proceed as follows: Make sure that the door is closed; · Push the facing panel down until the whole of the display is visible. To return the facing panel · to the normal position, push it back up. WARNINGS ! · · · · · The facing panel can only be lowered with the door closed; Once the facing panel has been lowered the door cannot be opened (see diagram); Before opening the door of the dishwasher make sure that the facing panel is in the high position; Never lower the facing panel and close the door simultaneously; first close the door, then lower the facing panel; never raise the facing panel and open the door simultaneously; first bring the facing panel to the high position, then open the door. COMPLIANCE WITH THE INSTRUCTIONS PROVIDED ABOVE ENSURES THE CORRECT OPERATION BOTH OF THE SLIDING SYSTEM OF THE FACING PANEL AND OF THE DISHWASHER ITSELF. 33 User instructions 4. The optical level indicator on the side of the cap should be completely obscured. Refill the rinse aid when the optical level indicator becomes clear again, or when the rinse aid warning light illuminates. Use a cloth to remove any spillage of rinse aid which might lead to the formation of excess foam. ADJUSTING THE RINSE AID DISPENSER SETTING The dishwasher is factory set for medium water hardness. However it possible to change the setting by turning the dispenser's selector to the desired position: the amount of rinse aid dispensed is proportional to the selector position. The setting must be increased when the washed dishes appear dull or have circular staining. · · · To adjust the rinse aid setting, rotate the dispenser cap through a quarter turn in an anticlockwise direction and remove it. Then use a screwdriver to rotate the rinse aid selector to the desired position. Replace the cap, turning it clockwise. 36 User instructions · · The amount of rinse aid must be increased if the washed dishes appear dull or feature circular stains. If, on the other hand, the dishes are sticky or have white streaks, it is necessary to reduce the rinse aid setting. ADDING THE DETERGENT To open the detergent dispenser cap, lightly press the button P. During the washing cycle, the dispenser will be opened automatically. · When a SUPER program is selected, in addition to the normal dose of detergent, it is necessary to add an additional amount inside compartment G or H. For optimal washing results it is important to use a good quality detergent. The detergent packs must be sealed and stored in a dry place to prevent the formation of lumps which may negatively affect washing results. [. . . ] CLEANING THE WATER INTAKE FILTER The water intake filter A located at the outlet of the water supply tap needs to be cleaned periodically. After having closed the water supply tap, unscrew the end of the water intake hose, remove the filter A and clean it delicately under running water. Reassemble filter A in its seat and carefully screw the water intake hose back into position. CLEANING THE SPRAY ARMS The spray arms can be easily removed for periodic cleaning of the nozzles, to prevent possible clogging. Wash them under running water and carefully replace them in their seats, checking that their rotary movement is in no way impeded. [. . . ]