User manual SMEG STU1846 MANUALE D'INSTALLAZIONE

[. . . ] DISHWASHER INSTALLATION INSTRUCTIONS CONTENTS CONTENTS Contents 1 2 3 3. 1 3. 2 4 5 5. 1 5. 1. 1 5. 1. 2 5. 2 5. 2. 1 5. 2. 1. 1 5. 2. 1. 2 5. 2. 2 5. 3 5. 3. 1 5. 3. 2 5. 3. 3 5. 4 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 INSTALLATION MATERIAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Kit supplied with dishwasher (models sta_4645/sta_8743) . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To assure stability, only install built-in appliances under continuous worktops, securing them to the adjacent kitchen units or worktop with screws. BUILDING-IN A DISHWASHER UNDERNEATH A CERAMIC HOB IS ABSOLUTELY FORBIDDEN. A DISHWASHER CAN BE BUILT-IN UNDERNEATH A CONVENTIONAL HOB PROVIDED THERE IS NO BREAK IN THE KITCHEN WORKTOP, AND THE DISHWASHER AND HOB ARE INSTALLED AND SECURED CORRECTLY, SO THAT NO HAZARDS ARE GENERATED. MAKE SURE THE DISHWASHER HAS BEEN CORRECTLY INSTALLED AND GROUNDED BY A QUALIFIED FITTER. THE MANUFACTURER DECLINES ALL RESPONSIBILITY FOR DAMAGE TO PERSONS OR PROPERTY RESULTING FROM THE FAILURE TO GROUND THE APPLIANCE OR FROM A DEFECTIVE GROUND CONNECTION. BEFORE PROCEEDING WITH INSTALLATION, DISCONNECT THE MAINS POWER SUPPLY FROM THE WORK AREA. Only for free-standing models • It is strictly forbidden to mount a hob over a free-standing dishwasher. EN 12 Rev 0. 0 11 EN INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS • If the appliance is not in a niche and can therefore be accessed on one side, cover the door hinge area for safety reasons (cutting hazard). Covers are available as accessories from specialized retailers or from the Technical Service Centre. • To build in the dishwasher, purchase the relative kit from specialized retailers or from the Technical Service Centre. EN 5. 1 5. 1. 1 Leveling Mounting the feet (only for some models) Turn the appliance upside-down (see fig. 5-01) of the foot and then fit the supplied washer; do this on both feet. Screw the feet onto the appliance until the washers touch the base; the two feet must be manually adjusted to the same height to prevent excessive differences in height between one foot and the other. TWO PEOPLE WEARING SAFETY GLOVES ARE NEEDED TO TURN THE DISHWASHER UPSIDE-DOWN. A B Fig. 5-01 Rev 0. 0 13 12 EN INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 5. 1. 2 Levelling the appliance Level the appliance using the relative adjustable feet (e. g. : ref. 5-02); use an open-ended wrench to rotate the feet until the dishwasher is perfectly level. Some models are fitted with just one rear foot which can be adjusted with a screw located at the bottom front of the appliance (ref. THE DISHWASHER MUST ALWAYS BE CONNECTED TO THE WATER SYSTEM WITH NEW HOSES; OLD OR USED HOSES MUST NEVER BE REUSED. 16 Rev 0. 0 15 EN INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 5. 2. 1. 1 Connecting to the water tap Connect the inlet hose to a threaded ¾” gas cold water tap, fitting the supplied filter (ref. Firmly secure the hose by tightening the relative ring nut with your hands (ref. 5-06); finish by tightening another ¼ turn using a pair of plumbing pliers. The dishwasher can be filled with water at a temperature of less than 60°C (140°F). If the appliance is filled with hot water, washing times will be reduced by about 20 minutes, but efficiency will be slightly impaired. Make the connection to the domestic hot water tap using the same methods described for connecting the appliance to the cold water tap. A rubber hose connected to a sink spray may burst if installed on the same pipes feeding the dishwasher. [. . . ] TWO PEOPLE WEARING SAFETY GLOVES ARE NEEDED TO PUSH THE DISHWASHER INTO PLACE. Fig. 5-18 26 Rev 0. 0 25 EN INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS 5. 3. 2 Procedure for mounting the door panel Mount the door panel. Place the template on the inner surface of the panel, centering it along the upper side and matching up the reference locators (ref. Remove the template and use a drill with a suitable bit to make holes at the points marked on the panel. A EN A Fig. [. . . ]