User manual SMEG TR90X

[. . . ] Contents 1 Instructions 1. 1 1. 2 1. 3 1. 4 1. 5 1. 6 1. 7 2. 1 2. 2 2. 3 2. 4 2. 5 General safety instructions Identification plate Manufacturer liability Appliance purpose Disposal This user manual How to read the user manual General Description Cooking hob Control panel Other parts Available accessories Instructions First use Using the accessories Using the storage compartment Using the hob Using the oven Cooking advice Programmer clock Instructions Cleaning the appliance Removing the door Cleaning the door glazing Cleaning the inside of the oven Extraordinary maintenance Gas connection Adaptation to different types of gas Electrical connection Positioning 40 40 41 41 41 41 42 42 2 Description 43 43 43 44 45 45 3 Use 3. 1 3. 2 3. 3 3. 4 3. 5 3. 6 3. 7 3. 8 4. 1 4. 2 4. 3 4. 4 4. 5 4. 6 5. 1 5. 2 5. 3 5. 4 47 47 48 48 50 50 51 53 54 4 Cleaning and maintenance 58 58 58 59 60 60 61 5 Installation 63 63 66 71 72 We advise you to read this manual carefully, which contains all the instructions for maintaining the appliance's aesthetic and functional qualities. For further information on the product: www. smeg. com 39 EN Instructions 1 Instructions 1. 1 General safety instructions Risk of personal injury • During use the appliance and its accessible parts become very hot. • Keep children under eight years of age at a safe distance if they are not constantly supervised. • This appliance may be used by children aged at least 8 and by people of reduced physical and mental capacity, or lacking in experience in the use of electrical appliances, as long they are supervised or instructed by adults who are responsible for their safety. [. . . ] • To defrost meat, use the rack placed on the second level and a tray on the first level. In this way, the liquid from the defrosting food drains away from the food. • For successful proving, a container of water should be placed in the bottom of the oven. To save energy • Stop cooking a few minutes before the time normally used. Cooking will continue for the remaining minutes with the heat which has accumulated inside the oven. • Reduce any opening of the door to a minimum to avoid heat dispersal. • Keep the inside of the appliance clean at all times. 3. 8 Programmer clock 1 Minute minder timer key 2 Cooking duration key 3 End of cooking key 4 Value decrease key 5 Value increase key The programmer clock controls exclusively the right multifunction oven and has not any control on the other ovens. 54 Use Setting the time On the first use, or after a power failure, the digits will be flashing on the appliance's display. The symbol on the display indicates that the appliance is ready to start cooking. Timed cooking Timed cooking is the function which allows a cooking operation to be started and then ended after a specific length of time set by the user. The display will shows the digits and the symbol displayed between the hours and the minutes. 5 seconds without pressing any key in order for the function to activate. On the display, symbol turns off, symbol flashes and the buzzer sounds. To reset the set program, press keys and at the same time and switch off the oven manually. Programmed cooking Programmed cooking is the function which allows a cooking operation to be started at a set time and then ended after a specific length of time set by the user. Set the cooking time as described in the previous point “Timed cooking”. The sum of the current time plus the pre-set cooking duration will appear on the display. 5 seconds without pressing any key in order for the function to activate. On the display, symbol turns off, symbol flashes and the buzzer sounds. Minute minder timer The minute minder timer does not stop the cooking operation but rather informs the user when the set time has run out. The display shows the digits and the indicator light flashing between the hours and the minutes. 5 seconds without pressing any key to finish setting the minute minder. After the minute minder timer has been programmed, the display will go back to showing the current time; to display the remaining time, press . [. . . ] • The tightening torque of the screws of the terminal supply wires must be 1. 5 - 2 Nm. General information Check the grid characteristics against the data indicated on the plate. The identification plate bearing the technical data, serial number and brand name is visibly positioned on the appliance. Perform the ground connection using a wire that is 20 mm longer than the other wires. [. . . ]