User manual SONY MHC-ZX30AV

[. . . ] 4-227-889-12(1) Mini Hi-Fi Component System Operating Instructions MHC-ZX30AV ©2000 Sony Corporation WARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. NOTICE FOR THE CUSTOMERS IN CANADA CAUTION TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. ENERGY STAR® is a U. S. As ENERGY STAR® Partner, Sony Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. This stereo system is equipped with the Dolby B-type noise reduction system*. [. . . ] Move the multi stick toward b or B repeatedly to select "1 Way" to record on one side, or "Cycle" ( or "Relay") to record on both sides, then press PUSH ENTER. Press REC PAUSE/START. Recording starts. 2 x Multi stick PUSH ENTER 4 8 9 To Start playing the source to be recorded. Press x. REC PAUSE/START. Stop recording Pause recording To cancel the menu operation Press MODE SELECT. 3, 8 . > 1 2 3 Insert a recordable tape into deck B. 1 Press FUNCTION repeatedly until the source you want to record (e. g. , CD) appears. The TAPE B N indicator (for front side) lights. 28 Tips · If you want to record from the reverse side, press TAPE B n to light its indicator after pressing REC PAUSE/START in step 3. · When you want to reduce the hiss noise in low-level high-frequency signals, do the following procedure after pressing REC PAUSE/START in step 3. 1 Press MODE SELECT repeatedly to select "Set Up Mode", then press PUSH ENTER. 2 Move the multi stick toward b or B repeatedly to select "TAPE Set Up ?", then press PUSH ENTER. 3 Move the multi stick toward b or B repeatedly to select "DOLBY NR Set Up ?", then press PUSH ENTER. 4 Move the multi stick toward b or B repeatedly to select "On", then press PUSH ENTER. To return to the original setting, repeat steps 1 through 4 and select "Off" in step 4. or > to select tracks during rec pause mode (after pressing REC PAUSE/START in step 3 and before pressing again in step 8). Recording a CD by specifying track order -- Program Edit You can record tracks from all the CDs in the order you want. When programming, make sure the playing times for each side do not exceed the length of one side of the tape. ?/1 (Power) The CD Player Deck The Tape 2 12 x 3, 13 17 11 Multi stick PUSH ENTER H hH hH . m > M x X 10 continued 29 Recording a CD by specifying track order (continued) 9 1 2 3 4 5 6 Place a CD and insert a recordable tape into deck B. Press FUNCTION repeatedly until "CD" appears in the display. Press MODE SELECT repeatedly to select "Set Up Mode", then press PUSH ENTER. Move the multi stick toward b or B repeatedly to select "CD Set Up ?", then press PUSH ENTER. Move the multi stick toward b or B repeatedly to select "Program Set ?", then press PUSH ENTER. Move the multi stick toward v or V repeatedly to select a CD. If you want to program all the tracks on a CD at once, select a CD in this step, then skip step 7 and continue with step 8. To program additional tracks to be recorded on side A, repeat steps 6 through 8. Skip step 6 to select tracks from the same disc. 10 Press X on the remote to insert a pause at the end of side A. "P" appears in the display and the total playing time resets to "0m00s" in the display. 11 Repeat steps 7 and 8 for tracks from the same disc or steps 6 to 8 for tracks from another disc to program the remaining tracks to be recorded on side B. 12 Press CD SYNC. Deck B stands by for recording and the CD player stands by for playback. The TAPE B N indicator (for front side) lights and the REC PAUSE/START button flashes. 13 Press MODE SELECT repeatedly to select "Set Up Mode", then press PUSH ENTER. 7 Move the multi stick toward b or B repeatedly to select the desired track. Disc number Track number PROGRAM 14 Move the multi stick toward b or B repeatedly to select "TAPE Set Up ?", then press PUSH ENTER. Total playing time (including selected track) 8 Press PUSH ENTER. The track is programmed. When all the tracks are selected, "AL" appears in the display and all the tracks are programmed as one step. The program step number appears, followed by the total playing time. 30 15 Move the multi stick toward b or B repeatedly to select "Direction Set Up ?", then press PUSH ENTER. Tip When you want to reduce the hiss noise in low-level high-frequency signals, do the following procedure after pressing CD SYNC in step 12 in the previous page. [. . . ] Demagnetize them (see "Demagnetizing the tape heads" on page 54). Demagnetize them (see "Demagnetizing the tape heads" on page 54). After pressing N (n) or A, there is a mechanical noise, "EJECT" appears in the display, and the unit enters standby mode automatically. Eject the tape and turn the power back on. If other troubles not described above occur, reset the system as follows: 1 Unplug the power cord. [. . . ]