User manual SONY RM-VL600

[. . . ] 2-674-860-12 (1) Integrated Remote Commander Operating Instructions RM-VL600 © 2006 Sony Corporation For the customers in the U. S. A. WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] 2 Reprogram only the power-on signal of the air-conditioner on the button of the Commander by following the steps of "Programming signals of another remote controlLearning Function" (page 16). 3 Program the power-off signal of the air-conditioner on another button of the Commander. The two buttons of the Commander have been programmed with the power-on signal and the power-off signal of the air-conditioner respectively, so that you can operate the airconditioner with the Commander. SET VCR during data erasing data erasing complete Notes · With this operation, you can only erase the "learned" functions of all buttons for a specific component. · To erase a single "learned" function of a Component Select button, see page 22. 3 Press SET to finish setting. To cancel erasing, press SET. 24 Advanced Features Controlling the Volume of Visual Components Connected to an Audio System The Commander is factory preset based on the assumption that you hear the sound of your visual components from your TV speakers, and that you hear sound of your audio components from the loudspeakers connected to your amplifier. For example, to control the volume while using a VCR, you don't need to press the TV button to control the TV volume. The following table shows the factory setting of which volume would be controlled for each component. Component Select button TV VCR CBL DVD SAT AMP CD TAPE Controls the volume of TV TV TV TV TV amplifier amplifier amplifier To change the Factory Preset of the Volume Control 1 TV/VIDEO SET POWER TV VCR VIDEO1 DVD CD SAT TAPE CBL AMP AUX VIDEO2 1 TUNER 2 CD 3 TAPE 4 MD 5 TV 6 PHONO 7 VOL 8 DVD 9 ENT 0 DIGITAL /ANALOG TWIN VIEW CH SLEEP 2 RECALL MENU INFO MUTING GUIDE 1 OK EXIT TOOLS SYSTEM CONTROL A B C D 1 Press and while holding SET, press MENU. MENU SET + However, if your visual components are connected to an audio system, you may want to hear TV or VCR sound from the loudspeakers via your amplifier or DAV, not from your TV speakers. In this case, you need to change the factory preset so that you can control the volume of your visual components without first having to switch to the amplifier or DAV. The SET indicator lights up. SET Continued 25 Controlling the Volume of Visual Components Connected to an Audio System (continued) To set only the audio components' volume controls to AMP Press VOL ­ while holding MUTING pressed. Only AMP lights up when you press these buttons, and then turns off when you release them. Press and while holding VOL­, press MUTING. TV VCR DVD CD SAT TAPE CBL AMP 2 While holding MUTING pressed, press VOL + or VOL ­. To set all volume controls to AMP Press VOL + while holding MUTING pressed. All Component Select buttons light up when you press these buttons, and then turn off when you release them. Press and while holding VOL+, press MUTING. TV VCR DVD CD SAT TAPE CBL AMP Volume control setting complete. TV VCR DVD CD SAT TAPE CBL AMP Volume control setting complete. TV VCR DVD CD SAT TAPE CBL AMP Visual components are: TV, video cassette recorder, analog cable box, digital cable box, digital satellite tuner, DVD player, digital video recorder Audio components are: CD player, MD player, cassette deck, amplifier, DAV To cancel setting, press SET. Notes · If you used the Learning function to program the VOL +/­ or MUTING buttons to send a signal to a component, the procedure above will not change the function of the VOL +/­ and MUTING buttons. 26 Adding an Extra Function to the Component Select Buttons Programming the Power-On command of the selected component just by pressing that Component Select button (for Sony components only) When a code number of a Sony component is set to a Component Select button, the Power-On signal is automatically programmed to the button. You can select the desired component and power it on by just pressing that Component Select button. Example: To clear the Power-on command 1 Press and while holding SET, press MENU. MENU SET + The SET indicator lights up. SET 2 While holding POWER pressed, press the desired Component Select button. While the POWER button is pressed, the Component Select buttons that Sony components are set to flash in the following order. TVtDVDtSATtCBLt VCRtCDtTAPEtAMP The Component Select buttons that Sony components are not set to do not flash. TV/VIDEO SET POWER 1 2 TV VCR VIDEO1 DVD CD SAT TAPE CBL AMP AUX VIDEO2 1 TUNER 2 CD 3 TAPE 4 MD 5 TV 6 PHONO 7 VOL 8 DVD 9 ENT 0 DIGITAL /ANALOG TWIN VIEW CH SLEEP INFO MUTING GUIDE RECALL MENU 1 OK EXIT TOOLS SYSTEM CONTROL A B C D Continued 27 To cancel the setting, press SET. To program the Power-On command Repeat the same procedure, pressing the desired Component Select button. Notes · If the component code of a non-Sony brand has been set on a Component Select button, you cannot program the Power-On function on it. If you change the component code (page 10) after setting the Power-On function, the Power-On function is cleared. (The Component Select button flashes twice to indicate that you cannot set this function. ) · Even if you used the Learning function (page 16) to program a signal on a Component Select button, you can program the Power-On function on that button but it cannot be used. If you clear the "learned" function on that button, you can use the Power-On function. 28 Executing a Series of Commands -- System Control Functions With the System Control function, you can program a series of operating commands, and execute them by pressing just one button. You can program up to 16 consecutive operation steps to each of the SYSTEM CONTROL buttons (A ­ D). If you have set the System Control function for a Component Select button (page 33), the execution of the programmed commands begins when you press the Component Select button for more than 2 seconds. When executing the programmed commands, each remote commander signal is transmitted. Example: To watch a video, you can set a series of operations as follows: Power on the TV. r Start video playback. 1, 3 TV/VIDEO SET POWER TV VCR VIDEO1 DVD CD SAT TAPE CBL AMP AUX VIDEO2 1 TUNER 2 CD 3 TAPE 4 MD 5 TV 6 PHONO 7 VOL 8 DVD 9 ENT 0 DIGITAL /ANALOG TWIN VIEW CH 2 RECALL MENU SLEEP INFO MUTING GUIDE OK EXIT TOOLS SYSTEM CONTROL A B C D 1 Continued 29 Example: To program the procedure above to the SYSTEM CONTROL B button To program a new series of operations for those buttons which already have a control program set Erase the program (page 31). Notes · If you interrupt the procedure at any point for over 20 seconds, the setting mode ends and the series of commands will be programmed up to that point. In this case, clear the program (page 31) and start again from Step 1 to set the entire program from the beginning. · If a SYSTEM CONTROL button has already "learned" a remote control signal (page 16), you can program a System Control function (System Control Macro), but the function does will not work until you clear the Leaning function. [. . . ] To turn on the display. KEY DISPLAY qjOK qdCHANNEL +/­ 2DIGITAL/ ANALOG (REPLAY*1) FUNCTION To bring up the Station Index when a program guide is not displayed. Channel up: + Channel down: ­ To replay Or to go into REC/ REVIEW mode during play (After about 5second rewind, replay begins). 4INFO (DISPLAY) 7CLEAR 6GUIDE (EPG) 8m 8N 8M 8REC z To clear the setting. qgRECALL To select the channel previously selected. *1 This key corresponds to Tivo service or the replay service. *2 In order to avoid recording by mistake, the REC z button does not work by itself. Continued 43 Table of Preset Functions (continued) CD KEY DISPLAY 9POWER 11 ­ 9, 0 FUNCTION To turn on and off. [. . . ]