User manual SONY STR-SE391

[. . . ] As the main plug is used to disconnect the unit from the mains, connect the unit to an easily accessible AC outlet. Should you notice an abnormality in the unit, disconnect the main plug from the AC outlet immediately. Do not expose batteries or apparatus with batteryinstalled to excessive heat such as sunshine, fire or the like. The unit is not disconnected from the mains as long as it is connected to the AC outlet, even if the unit itself has been turned off. [. . . ] This mode is ideal for MP3 and other compressed music. 82GB To listen to music through headphones connected to the receiver Sound field Headphone (2ch) Effect This mode is selected automatically if you use headphones when "2ch Stereo" mode or A. F. D. Standard 2 channel stereo sources completely bypass the sound field processing and multi-channel surround formats are downmixed to 2 channels. This mode is selected automatically when you use headphones when sound field is selected for movie/music. It allows you to experience a theater-like environment while listening through a pair of headphones. Outputs the analog signals without processing by the tone, sound field, etc. This mode is selected automatically if you use headphones when the multichannel input is selected. Outputs the front analog signals from the MULTI CHANNEL INPUT jacks. Headphone Theater D CS Headphone (Direct) Headphone (Multi) Enjoying Surround Sound To turn off the surround effect for MUSIC Press 2CH/A. DIRECT or A. F. D. Notes · The sound fields for music do not work when the multi-channel input is selected. · The sound fields for music do not work when DTSHD signals with a sampling frequency of higher than 48 kHz are being received. · The sound fields for music do not work when Dolby TrueHD signals with a sampling frequency of higher than 96 kHz are being received. · If you set up the sound field during DTS 96/24 signal reception, the signal will be played back only at 48 kHz. Use an IR repeater when you install the receiver in a place where signals from the remote cannot reach. 88GB Making a multi-zone connection 1:Zone 2 connections 1 Outputs sound from speakers in zone 2 using the SURROUND BACK SPEAKERS terminals of the receiver. Main zone Zone 2 STR-SE391 IR REMOTE IN TV monitor A B ZONE 2 VIDEO OUT* B Using Multi-zone Features RM-AAP026 SURROUND BACK SPEAKERS 2 Outputs sound from speakers in zone 2 using the receiver and another amplifier. Main zone Zone 2 B TV monitor B IR REMOTE IN STR-SE391 C A ZONE 2 VIDEO OUT* ZONE 2 AUDIO OUT RM-AAP026 A IR repeater (not supplied) B Speakers C Sony Amplifier/Receiver * You can also connect to the COMPONENT VIDEO ZONE 2 OUT jack. 89GB 2:Zone 3 connections Main room Zone 3 B B IR REMOTE IN STR-SE391 C A ZONE 3 AUDIO OUT RM-AAP026 A IR repeater (not supplied) B Speakers C Sony Amplifier/Receiver 90GB Making a zone 2 configuration using ZONE 2 VIDEO OUT (RJ45 jack) ZONE 2 VIDEO OUT (RJ45 jack) is used only for custom installation by a qualified person. ZONE 2 VIDEO OUT (RJ45 jack) is a jack that sends a source video signal to the component video input for zone 2. Note This jack is not for an Ethernet LAN connection. ZONE 2 VIDEO OUT (RJ45 jack) connection The RJ45 pinouts use the T568B standard. Zone 2 Component Video Balun CAV-CVB1 TV monitor Using Multi-zone Features CAT5 cable Component video cable ZONE 2 VIDEO OUT (RJ45 jack) Note CAV-CVB1 (Component Video Balun) must be used. Other types will cause trouble and may void your warranty. RJ45 Video Pinout The RJ45 pinouts use the T568B standard. Refer to the illustration below. Pinout A Pin 1 B Pin 2 C Pin 3 D Pin 4 E Pin 5 F Pin 6 G Pin 7 H Pin 8 BLUE/Pb (R) BLUE/Pb (T) GREEN/Y (R) GND +11V GREEN/Y (T) RED/Pr (R) RED/Pr (T) Wire color White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown continued 91GB CAT5 cable Be sure to verify the CAT5 wiring connection is correct. Use Category 5e or Category 6 cable. Wire color RJ45 connector White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown Pin No. 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 CAT5 cable RJ45 connector 92GB 5 Setting the speakers in zone 2 When the speakers in zone 2 are connected to the SURROUND BACK SPEAKERS terminals of the receiver (page 89), make the setting so that the sound selected in zone 2 is output from the speakers connected to the SURROUND BACK SPEAKERS terminals. Press V/v to select "Speaker Pattern, " to select the pattern that has no surround back speakers. Press V/v repeatedly to select "Sur Back Assign, " then press . Press V/v to select "ZONE2, " then press . 6 7 8 AMP To exit the menu Press MENU. Using Multi-zone Features V/v/b, RETURN/ EXIT O MENU 1 2 3 4 Press AMP. The receiver can be operated using the remote. Press MENU. The menu is displayed on the TV screen. Press V/v repeatedly to select " Settings, " then press or b. [. . . ] ­ "AMP" if you want to listen to the sound from the receiver. · You cannot listen to the sound of a component connected to the receiver while a TV is selected as the input on the receiver. ­ Change the input of the receiver to HDMI when you want to watch a program on a component connected to the receiver. ­ Select the component or input you want to watch when you watch a program on the component connected to the TV. [. . . ]