User manual SONY VPCEG1BFX/B

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SONY VPCEG1BFX/B. We hope that this SONY VPCEG1BFX/B user guide will be useful to you.


SONY VPCEG1BFX/B : Download the complete user guide (2108 Ko)

Manual abstract: user guide SONY VPCEG1BFX/B

Detailed instructions for use are in the User's Guide.

[. . . ] 8 8 8 9 0 Insure proper Insure proper ground exists ground exists before use. Before use 1 2 You should have the wall receptacle and circuit checked by a qualified electrician to make sure the receptacle is properly grounded. If you have a standard two-prong wall receptacle, it is very important to have it replaced with a properly grounded threeprong wall receptacle, installed by a qualified electrician. This product must be connected to a supply circuit of the proper voltage and frequency. [. . . ] Equivalent lengths of duct pieces are based on actual tests and reflect the requirements for good venting performance with any vent hood. Indd 5 2012-07-25 7:50:44 General information Damage - Shipment/Installation • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. € If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. € If the unit is damaged by the installer (if other than the customer), repair or replacement must be made by arrangement between the customer and installer. Tools you will need Parts included HARDWARE PACKET PART Wood Screws (¼˝ x 2˝) Toggle Bolts (and wing nuts) (3/16˝ x 3˝) Self-aligning Machine Screws (¼˝ - 28 x 3 ¼˝) Nylon Grommet (for metal cabinets) QUANTITY 1 TOP CABINET TEMPLATE TOP CABINET N IOTEMPLATE LLAT S INSTA UCTION R REAR INST WALL TEMPLATE REAR WALL TEMPLATE ADDITIONAL PARTS late emp T PART Top Cabinet Template Rear Wall Template QUANTITY 1 1 2 Installation Instructions 1 2 1 Separately Packed Grease Filter 2 Mounting space You will find the installation hardware contained in a packet plate the unit. Check to make sure you have all with Template Tem theseemplate T parts. Indd 6 2012-07-25 7:50:45 General information Tools you will need # 1 and #2 Phillips screwdriver Pencil Ruler or tape measure and straight edge Carpenter square (optional) Tin snips (for cutting damper, if required) Scissors (to cut template, if necessary) Electric drill with 3/16˝, ½˝ and ⅝˝ drill bits Filler blocks or scrap wood pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Gloves Saw (saber, hole or keyhole) Stud finder or Hammer (optional) Safety goggles Level Duct and masking tape Mounting space 12˝ max. Bottom edge of the cabinet needs to be 30˝ or more from the cooking surface. Backsplash NOTES: • The space between the cabinets must be 30˝ wide and free of obstructions. • This microwave oven is for installation over ranges up to 36˝ wide. € If you are going to vent your microwave oven to the outside, see the Hood Exhaust Section for exhaust duct preparation. Draw a Horizontal line on the wall at the bottom of the “Rear Wall Template”. Drill ⅝˝ holes for toggle bolts in 3 locations (Hole A, Hole B, Hole C) as shown in the illustration above. If the location of a hole lines up with a stud, drill a 3/16˝ hole for a wood screw. If none of these holes line up with a stud, find a stud in area E that lines up with a hole circle in Area E, and then drill a 3/16˝ hole into it for a wood screw. You must have at least one wood screw mounted firmly into a stud to support the weight of the microwave.  utside Back Exhaust (Horizontal Duct) O NOTE: This microwave is shipped assembled for Outside Top Exhaust (except for non-vented models). an exhaust adaptor is shipped assembled and attached to the filler-upper. Select the type of ventilation required for your installation and proceed to that section. Outside top exhaust (vertical duct) Adaptor in Place Adaptor in Place for Outside Top for Outside Exhaust B. recirculating (nonvented ductless) Top Exhaust See page 12 See page 12 A Charcoal Filter Accessory Kit is required for the nonvented exhaust. Installation procedure for exhaust adaptor and proper damper operation check NOTE: You must attach the house duct to the exhaust adaptor after installation is complete. [. . . ] ) IMPORTANT: The case damage that will occur from over tightening screws if you do not use filler blocks is not covered under warranty. NOTE: When mounting the microwave oven, thread the power cord through hole in the bottom of top cabinet. Lift the microwave, tilt it forward, and hook the slots at the back bottom edge onto the four lower tabs of the mounting plate. Use the top cabinet template to prepare the top cabinet You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SONY VPCEG1BFX/B




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SONY VPCEG1BFX/B will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.