User manual SONY XPLOD 52WX4

[. . . ] € When no car circuits are rated high enough, connect the unit directly to the battery. Ύ   ×2  Parts list • The numbers in the list are keyed to those in the instructions. € The bracket  and the protection collar  are attached to the unit before shipping. [. . . ] Before mounting the unit, use the release keys  to remove the bracket  from the unit. For details, see “Removing the protection collar and the bracket ()” on the reverse side of the sheet. € Keep the release keys  for future use as they are also necessary if you remove the unit from your car. Caution Handle the bracket  carefully to avoid injuring your fingers. Equipment used in illustrations (not supplied) In Abbildungen dargestellte Geräte (nicht mitgeliefert) Appareils utilisés dans les illustrations (non fournis) Apparecchiatura utilizzata nelle illustrazioni (non in dotazione) Apparatuur gebruikt in de afbeeldingen (niet bijgeleverd) Front speaker Frontlautsprecher Haut-parleur avant Diffusore anteriore Voorluidspreker Active subwoofer Aktiver Tiefsttöner Caisson de graves actif Subwoofer attivo Actieve subwoofer  Catch Note Before installing, make sure that the catches on both sides of the bracket  are bent inwards 2 mm (3/32 in). If the catches are straight or bent outwards, the unit will not be installed securely and may spring out. Rear speaker Hecklautsprecher Haut-parleur arrière Diffusore posteriore Achterluidspreker Power amplifier Endverstärker Amplificateur de puissance Amplificatore di potenza Eindversterker Connection example Notes • Be sure to connect the ground (earth) lead before connecting the amplifier. Connection diagram  To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. Warning A If you have a power antenna (aerial) without a relay box, connecting this unit with the supplied power supply lead  may damage the antenna (aerial). 1 182 mm 2 3 Dashboard Armaturenbrett Tableau de bord Cruscotto Dashboard   Fire wall Motorraumtrennwand Paroi ignifuge Parete tagliafiamma Brandschot  53 m m Claws Klammern Griffes Morsetti Klemhaken  Schéma de raccordement d’alimentation Le connecteur d’alimentation auxiliaire peut varier suivant le type de voiture. Ύ A B Auxiliary power connector Hilfsstromanschluss Connecteur d’alimentation auxiliaire Connettore di alimentazione ausiliaria Hulpvoedingsaansluiting Precautions • Choose the installation location carefully so that the unit will not interfere with normal driving operations. € Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperature, such as in direct sunlight or near heater ducts. € Use only the supplied mounting hardware for a safe and secure installation. Red Rot Rouge Rosso Rood Red Rot Rouge Rosso Rood Mounting angle adjustment Adjust the mounting angle to less than 45°. Yellow Gelb Jaune Giallo Geel Removing the protection collar and the bracket Before installing the unit, remove the protection collar  and the bracket  from the unit. ΍ Insert both release keys  together between the unit and the bracket  until they click. Mounting example Installation in the dashboard Notes • Bend these claws outward for a tight fit, if necessary (-2). € Make sure that the 4 catches on the protection collar  are properly engaged in the slots of the unit (-3). [. . . ] € Make sure that the 4 catches on the protection collar  are properly engaged in the slots of the unit (-3). How to detach and attach the front panel Before installing the unit, detach the front panel. Yellow Gelb Jaune Giallo Geel Yellow Gelb Jaune Giallo Geel switched power supply geschaltete Stromversorgung alimentation commutée alimentazione commutata geschakelde voeding Red Rot Rouge Rosso Rood Yellow Gelb Jaune Giallo Geel continuous power supply permanente Stromversorgung alimentation continue alimentazione continua continu voeding Retrait et fixation de la façade Avant d’installer l’appareil, retirez la façade. [. . . ]