User manual STRONG SRT 5510 MHP

[. . . ] Wait a few seconds after switching off the receiver before you move the receiver or disconnect any equipment. n It is a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical power consumption of the installed equipment. Please ensure that the electrical power supply corresponds with the voltage on the electrical identification plate at the back of the receiver. If the receiver does not operate normally even after strictly following the instructions in this user manual, it is recommended to consult your dealer. 1. 2 Storage Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture. [. . . ] The receiver will start an automatic channel scan to find the DVB-T channels that are available in your area. Update: This function allows to re-allocate the channels list and to add channels without modifying the positions of the actual channels. In case of first time installation this function involves as function "First Installation Search". Add One Channel: This function allows searching for specific channels and frequencies. This is an option recommended for experienced users who know the channel number, frequency and the bandwidth. Select "Bandwidth" by pressing pq and the bandwidth by pressing tu and press OK to start searching. In the event, that no channel could be found, change the direction of your antenna and repeat "Install". 7 PART 2 · English 5. 0 USAGE In the main menu you'll find all important settings and functions. Your Guide TV Channels Radio Channels Application Channels Stored Services Program Guide Your Preferences Display options Time and Date Channel Number Channel Banner Timeout Volume Bar Application Autostart Language options On-Screen Language First Audio Language Second Audio Language First Subtitle Language Second Subtitle Language Dolby Digital Sort channels TV Channels Radio Channels Application Channels Timer Enable Timer Channel List Channel Name Start Date Start Time End Time Frequency Installation (PIN Input necessarily) System Setup TV Aspect Ratio Display Format TV SCART Output VCR SCART Output Amp. Power OTA in standby Chance PIN Code 8 PART 2 · English Channel Search Install Update Add One Channel Time Setup Factory Settings Internet Setup Decoder Status Signal Level System Info Decoder Upgrade Loader Status Help Using Your Box Using Your PIN MHP Software Update 5. 1 Your Guide 5. 1. 1 TV Channels Select "TV channels" with the buttons pq and press OK. 5. 1. 2 Radio Channels Select "Radio Channels" with the buttons pq and press OK. 5. 1. 3 Programme Guide (EPG) EPG (Electronic Program Guide) is transmitted by broadcasters to display information about program content. To access the EPG function directly during TV/Radio, press the key EPG on your remote control. It will open the EPG which contains the following information: Actual date and hour Actual programme n Actual and following programs (if available) n Title of the programme (if available) n n For scrolling, use pq. Set the "Channel List" and "Channel Name" by using the tu keys. Use the numbered buttons to type in the "Start Date", "Start Time" and "End Time". In "Frequency" you can choose how often the timer should be activated: "once", "daily" or "weekly". The "Duration" shows you for how long the "Timer" is activated. To confirm the settings press OK. 10 PART 2 · English 7. 0 INSTALLATION The change of some menu settings can jeopardize the correct operation of the receiver. We recommend therefore, to read this section of the manual carefully before proceeding. The factory setting is "1 2 3 4". 7. 1 System Setup English 11 7. 1. 1 TV Aspect Ratio This function allows you to adjust the format to your TV screen (4:3 or 16:9). 7. 1. 2 Display Format This function allows the receiver to adapt automatically to the picture format. Ignore: the receiver adjusts the picture automatically to the TV screen by compressing. [. . . ] Wait 30 seconds and connect to mains power again and now check if the unit is working as expected. If the receiver does not work properly after checking the trouble shooting section, please contact the dealer. Don't open the receiver cover, it may cause an electrical shock due to high current voltage and the warranty of your receiver will be void if the receiver has been opened. Symptoms The green/red lights on front panel do not light up No picture and sound Cause The power cord is not plugged in TV is set to wrong channel Solution Check that the power cord is plugged in to the wall outlet. [. . . ]