User manual STRONG SRT 6020

[. . . ] Digital Free-To-Air Satellite Receiver SRT 6020 User Manual Picture similar Figure 1 1 2 3 4 5 3 4 8 9 10 11 COAXIAL S/PDIF RS-232 ANT IN TO TV ON OFF AC 90-240 V~ 50/60 Hz Max. 20 W SAT IN SAT OUT TV SCART VCR SCART S-VIDEO Figure 2 1 2 5 6 7 TELEVISION Fixed Satellite Dish COAXIAL S/PDIF RS-232 ANT IN TO TV ON OFF AC 90-240 V~ 50/60 Hz Max. 20 W SAT IN COAXIAL SAT OUT TV SCART VCR SCART S-VIDEO S/PDIF RS-232 ANT IN TO TV ON OFF AC 90-240 V~ 50/60 Hz Max. pointed at HotBird) SAT OUT TV SCART VCR SCART S-VIDEO Figure 3 TELEVISION COAXIAL S/PDIF RS-232 ANT IN TO TV ON OFF AC 90-240 V~ 50/60 Hz Max. [. . . ] After selection of a satellite from the satellite list, the Configure Antenna menu will appear, please set the LNB Type, LNB Low Freq, LNB High Freq, Band control, Polarisation control, DiSEqC Switch and Antenna mode. n Edit satellite If the parameters of the satellite were changed or the satellite is a new satellite, you must set the parameters of the satellite, such as LNB type, LNB low Freq, LNB High Freq, Transponder, LNB Power, 22k Tone, DiSEqC and Antenna Mode. Sequence of editing of satellite parameters is same as sequence of "Add satellite" and described in 4. 2 n Delete satellite If you want to delete a satellite, press the YELLOW key. Select OK and press the OK button to confirm. 9 English PART 1 · English 5. 2. 2 Auto Scan Press the GREEN key to set the scan mode to Free or Free+Scrambled. If mode is Free only "Free to Air" channels will be added to the channel list. If mode is Free+Scrambled all channels from selected satellite will be added to the channel list. Blind scan function is useful to scan new added satellite, but scan may take long time. Press the BLUE Key to set the scan type to NIT OFF or NIT ON while Blind Scan is set to OFF and to Quick Search or Detail Search while Blind Scan is set to ON. 5. 2. 3 Manual Scan In this menu, you can scan single transponder, add a new transponder, edit the transponder or delete the transponder. n Add Transponder: In this menu, you can add a new transponder to the system. Press the GREEN button, the Add Transponder sub-menu will appear on screen. n Edit Transponder: In this menu, you can edit a transponder in the system. Press the YELLOW button, the Edit Transponder sub-menu will appear on screen. Press LEFT/RIGHT to select OK, press the OK button to confirm. 5. 3 System setting In this menu, you can configure the systems such as Language Setting, OSD Style, Parental Control, TV Settings and Time Setting. 5. 3. 1 Preference 5. 3. 1. 1 Language Setting You can change the language of the OSD, preferred Audio and Subtitles. Use UP/DOWN to select the OSD language, Audio language or Subtitles language. Press OK or Right to enter the language list and Press UP/DOWN to select the language. Press OK to confirm. 10 PART 1 · English 5. 3. 1. 2 TV settings You can set the TV mode, Screen mode, Video output and Modulator setting. n TV mode In TV mode Screen press OK or RIGHT to select mode, press OK to confirm. If you don't know which standard your TV has, please select AUTO. n Screen mode In TV format Screen press OK or RIGHT to select 4:3 or 16:9, press OK to confirm. n Video output Press OK or RIGHT to select CVBS, RGB or S-Video, press OK to confirm. [. . . ] Electronic program guides that are transmitted by a broadcaster from a particular satellite to display information guide about a program content. Unscrambled broadcast which you can view for free 11 ~ 13GHz Frequency. It receives the signals reflected by the dish and converts them to signals that can be used by Satellite receiver. MPEG is a standard method for digital transmission of video and audio. [. . . ]