User manual STRONG SRT 6500CI

[. . . ] Digital Satellite Receiver with Cryptoworks Embedded and Common Interface SRT 6500 CI User Manual PART 1 · English TABLE OF CONTENTS English 1 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features and Accessories 2 2 2 2 3 4 4 4 5 7 7 7 8 8 9 10 10 10 16 21 25 26 2. 0 YOUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control 3. 0 CONNECTING THE RECEIVER 3. 1 To a TV set, using TV SCART connection. 3. 2 To a HiFi system and a TV set, using both A/V connections 3. 3 To a VCR and a TV set, using both SCART connections 3. 4 To VCR and a TV set, using build-in UHF modulator 4. 0 5. 0 STARTING UP FOR THE FIRST TIME SETUP AND OPERATION 5. 1 Before Setup 5. 2 Setup Menu 5. 3 Main Menu Settings 5. 4 General Viewing Information A1 A. 2 PROBLEM SOLVING SPECIFICATIONS PART 1 · English 1. 0 INTRODUCTION 1. 1 Safety Instructions DO NOT INSTALL YOUR RECEIVER: n In a closed or poorly ventilated cabinet; directly on top of or under any another equipment; on a surface which might obstruct the ventilation slots. DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES: n To direct sunlight or near any other equipment that generates heat; to rain or intense moisture; to intense vibration and to any not use a damaged power cord. It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical the receiver is not used for a long period of time, you should unplug the power cord from the wall socket. shock which may cause permanent damage to your receiver or to any magnetic objects, such as loudspeakers, transformers, etc. n Do cause an electric shock. n Never hazards. [. . . ] This mode recommended if you want to search channels of particular broadcaster only. Sub options are: "Free" ­ receiver will search only Free To Air channels "Free+Scr" ­ receiver will search for all channels Transponder: select index from the stored list Frequency: Polarity: FEC: Function: AGC Signal: value of transponder frequency in MHz Horizontal / Vertical / Right / Left Auto, 1/2, 2/3, 3/4, 5/6, 7/8 Append/Delete/Change Indicates received signal strength level Symbol Rate: value of symbol rate in kSymbols Per Second 5. 2. 3. 1 How to search for channels: Highlight "Tune method" field and press OK. Names of the found channels will be shown in the two columns: for TV and Radio separately. If you press OK button: search process will be interrupted and you can select one of the following options: n Save ­ to save all found channels n Unselect ­ to unselect some unwanted channels from the list. Use OK button to unselect channels and Vol t/u buttons to switch between TV and Radio list. Once you finish ­ press EXIT button, select "Save" and press OK. Only selected channels will be stored in the memory n Cancel ­ to cancel result of search. No channels will be stored in the memory If you press EXIT button: search process will be interrupted and no channels stoRED in the memory. 5. 2. 3. 2 How to add new transponder: n set "Tune method" to "TP" or "TP+NIT" focus to "Frequency" and enter value in MHz focus to "Symbol rate" and enter value in kSPS focus to "Polarity" and select value focus to "FEC" and select value or set "Auto" focus to "Function" select "Append" and press OK. New transponder n move n move n move n move n move will be added to the end of the list 13 English PART 1 · English 5. 2. 3. 3 How to delete present transponder: n set "Tune method" to "TP" or "TP+NIT" focus to "Transponder" and choose transponder you want to delete focus to "Function" select "Delete" and press OK. 5. 2. 3. 4 How to correct/edit parameters of the transponder: n set "Tune method" to "TP" or "TP+NIT" focus to "Transponder" and choose transponder you want to modify focus to "Frequency" and enter value in MHz focus to "Symbol rate" and enter value in kSPS focus to "Polarity" and select value focus to "FEC" and select value or set "Auto" focus to "Function" select "Change" and press OK. Modified data are n move n move n move n move n move n move stored in the memory. n Press EXIT to go back to the previous mode. 5. 2. 4 Setup Lock/PIN Press OK on `Setup Lock/PIN' in the Setup Menu. Set the Menu Lock, Change the PIN, enter the New PIN and confirm the Confirm PIN. n Use n Use CH p/q to move up and down the list. New PIN: Enter your new 4-digit code Confirm PIN: Confirm your new 4-digit code * Note: The default PIN is `1234' n Press EXIT to go back to the previous mode. 5. 2. 5 Time Setting Press OK on `Time Setting' in the Setup Menu. Set the Local Time, Sleep Time, Timer Status and Program the Timer. n Use n Use CH p/q to move up and down the list. Vol t/u to change the setting. 14 PART 1 · English Local Time: if you want to correct time and date then enter in format dd/ mm/yyyy - day ­ hh:mm Timer: select timer number Status: Disabled/Enabled. If Enabled ­ receiver will be turned on within selected channels at defined "start time" and turned off after "duration" interval Channel type: TV/Radio. If you use multi satellite installation ­ make sure to enter channel number in "All satellites" mode. Channel name: displayed automatically and depends from channel number. Start time: enter start time in format dd/mm/yyyy - day ­ hh:mm Duration: enter duration in hh:mm format. See "Program Guide" chapter of this manual. n Press OK to store settings and go back to the previous mode. 5. 2. 6 Factory Default Press OK on `Factory Set' in the Setup Menu. Confirm whether you wish to go back to the factory default settings. This function will return all settings of the receiver to factory default. [. . . ] If you press FAV button while listening to Radio ­ the list of Radio Favourite will be displayed. In case you didn't add any channels to Favourite lists, it would not appear. To change between Favourite lists you can use FAV button or press EXIT button while Favourite list is displayed. To return back to ALL channels mode press TV/Radio button. 23 English PART 1 · English 5. 4. 4 Program Guide Press EPG to access the electronic program guide, if available from the broadcaster. [. . . ]