User manual STRONG SRT 7500

[. . . ] Digital High Definition Satellite Receiver SRT 7500 User Manual Picture similar PART 2 · English TAblE of ConTEnTS 1. 0 InTRoDUCTIon 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 YoUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control Unit 2. 4 DEFAULT PIN-CODE: 0000 3. 0 ConnECTIonS 3. 1 Connecting to Satellite Dish 3. 2 Connecting to TV 3. 3 Connecting to Digital Audio Amplifier 3. 4 Connecting to computer by serial cable 4. 0 STARTInG UP foR THE fIRST TIME 4. 1 Language Selection 4. 2 Country Selection 4. 3 Antenna Installation 4. 4 Channel set-up 4. 5 Auto Search 5. 0 MAIn MEnU 5. 1 Program Table 5. 2 Favourites 5. 3 Installation 5. 4 Configuration 5. 5 Timers 5. 6 Games 5. 7 Media Browser 5. 8 CA System 6. 0 oTHER oPERATIonS 6. 1 Electronic Program Guide (GUIDE) 6. 2 Zapping and INFO banner 6. 3 Channel list and viewing mode A. 1 TRoUblESHooTInG A. 2 SPECIfICATIonS APPEnDIX: InSTAllATIon ASSISTAnCE 2 2 3 3 3 4 4 4 4 5 5 5 5 5 5 5 5 6 6 6 6 6 6 7 7 10 10 10 11 11 11 11 12 12 13 14 A1 STRONG declares that this item complies with the basic requirements and other relevant regulations of directives CE 2004/108/EEC and 73/23EEC RoHS 2002/95EEC Subject to alterations. In consequence of continuous research and development technical specifications, design and appearance of products may change. ASTRA is a registered trade mark of SES ASTRA, Eutelsat and HOT BIRD are registered trademarks of Eutelsat Communications, Irdeto is a trademark of Irdeto Access B. V. , all other product names are trademarks or registered trademarks of their respective owners. 10/2009 1 English PART 2 · English 1. 0 InTRoDUCTIon 1. 1 Safety Instructions The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of not isolated dangerous voltage with the inside of the product that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Recalculate Positions: Use this function to restore possible misaligned dish position. Setup one of the satellite 7 5. 3. 1. 1 DiSEqC 1. 2 Setup Menu English PART 2 · English positions and align your dish until signal strength and quality range are satisfying again and store this position. Now if you setup this specific SAT position correctly, you can apply realignment on the others by pressing oK at recalculate positions. note in order to avoid mechanical damage of your dish, please make sure the east and west limits in your motor are set correctly and dish would not hit any objects on its movement. 5. 3. 1. 2 GoTo X Setup Menu This GOTO X function allows you by entering your longitude and latitude to easily drive your motor to the desired satellite position. With bACK you can always cancel actions and exit the actual menu or submenu. Transponder Settings: If you have chosen a satellite from the installed SAT table, the corresponding reference transponder is already set. If you want to change the values for reference TP, press oK to enter its submenu. Use the nUMERIC buttons to enter a new value and use pq buttons to navigate. Turn to Satellite: Turns your antenna to the selected satellite position. note You can set new satellite positions by choosing User Satellites (User 1, 2, 3, 4). LNB Type, Low Frequency and High Frequency: These values are automatically setup for UNIVERSAL LNB configuration and cannot be changed, so other LNB's as UNIVERSAL cannot be supported!LNB Power: Here you can enable/disable LNB supply, use the tu buttons therefore. Adjust this setting to On, if this receiver is not connected to another receiver via loop-through. DiSEqC (Off / Tone A / Tone B / DiSEqC 1 / DiSEqC 2 / DiSEqC 3 / DiSEqC 4): You should set this according to connected switch position of the desired satellite. If your LNB device is connected directly to your receiver, we recommend to select Off mode. Use the u and pq buttons to select and press oK to confirm. Press oK to enter transponder database submenu. This frequency table contains the default transponder database of selected satellite. With bACK you can always cancel actions and exit the actual menu or submenu. The following operations are supported: Add: You can add new transponders to the list (frequency, polarisation, symbol rate). Press oK at Add and use the pq tu buttons for navigation and enter new values with the nUMERIC buttons. Delete: Use the pq buttons to mark the transponder you want to delete. Now use the pq tu buttons for navigation and enter new values with the nUMERIC buttons. Restore: This function will restore the transponder database to the one which was installed per default. [. . . ] note Please consider that sorting can be applied to desired satellite list, filtering can only be applied to all channels list. 6. 3 Channel list and viewing mode 6. 3. 1 favourite list In viewing mode you can use the FAV button to switch to favourite mode, another switching will bring you to FAV group and afterwards back to previous channel list mode. If you press oK in favourite mode the FAV channel list will be displayed. 12 PART 2 · English 6. 3. 2 Audio Mode and language Press A. foRMAT button in viewing mode. Further pressing will change audio channel between Left, Right and Stereo. Press the LANG button to select one of the available audio languages. 6. 3. 3 Video format Press the V. foRMAT button in viewing mode. [. . . ]