User manual STRONG SRT 8150

[. . . ] Digital High Definition Terrestrial Receiver SRT 8150 User Manual Picture similar Fig. 3 Fig. 4 PART 1 · English TABLE OF CONTENTS 1. 0 INTRODUCTION 1. 1 Safety Instructions 1. 2 Storage 1. 3 Equipment Set-up 1. 4 Features & Accessories 2. 0 YOUR RECEIVER 2. 1 Front Panel 2. 2 Rear Panel 2. 3 Remote Control Unit 3. 0 CONNECTIONS 3. 1 Connecting to Terrestrial antenna 3. 2 Connecting to TV & VCR 3. 3 Connecting to Digital Audio Amplifier 3. 4 Connecting to computer by serial cable 3. 5 Connecting to external USB Hard disk 4. 0 STARTING UP FOR THE FIRST TIME 4. 1 Language Selection 4. 2 Terrestrial Settings 5. 0 MAIN MENU 5. 1 Channel Organizer 5. 2 Terrestrial Search 5. 3 Installation 5. 4 Timer 5. 5 Application 6. 0 OTHER OPERATIONS 6. 1 Program Guide (EPG) 6. 2 Zapping and information banners 6. 3 Channel list and view mode 6. 4 PDR functions A. 1 TROUBLESHOOTING A. 2 SPECIFICATIONS 2 2 3 3 3 4 4 5 6 8 8 8 9 9 9 9 10 10 10 10 12 13 15 15 16 16 17 17 18 19 20 1 English PART 1 · English 1. 0 INTRODUCTION 1. 1 Safety Instructions Grounding, Polarization -- If this product is used with a specified AC adapter, the adaptermay be equipped with a polarized alternating current line plug (a plug with one blade wider than the other). This safety feature allows the plug to fit into the power outlet only one way. If you cannot insert the plug into the wall outlet, pull it out, reverse it, and then reinsert it. If the plug still fails to fit, contact an electrician and have the receptacle replaced n Protecting the Power Cord -- The power supply cord should be placed so it will not bewalked on. [. . . ] Press EXIT to cancel or OK to confirm. 5. 2 Terrestrial Search The Terrestrial Search menu contains following sub-menus: "Channel Setup" and "Terrestrial Settings" In first order make sure that Terrestrial settings are correct and corresponds to the country where you leave. 5. 2. 1 Channel set-up There are 2 possible ways of terrestrial channel search: Auto Scan (RED button) and Manual Scan (GREEN button). n Manual Search Select one or several frequencies by OK button then Manual Scan (GREEN button) to search for channels on selected frequencies. On completing the search, the receiver will save automatically the services information. 5. 2. 2 Terrestrial settings Use pqtu buttons to select your Country, Antenna Supply and Channel Numbering. n Antenna Supply: Select this option to ON in case you use active antenna powered through coaxial cable. n Channel Numbering: select this option to "Operator defined" in case your operator provide logical channel numbering feature. Otherwise select "Appearing order". 12 PART 1 · English 5. 3 Installation 5. 3. 1 Preference In this menu, you can set up your personal preferences. n OSD language, Audio language, Subtitle language Use pqtu buttons select the item and OK button to display the list. n Banner Timeout To set banner duration (how long information banner will be displayed on screen). n Transparency Use pqtu buttons to select the transparency level and OK button to display the list. n CAM messages To enable or disable displaying of messages from Conditional Access Module. Disabling of CAM messages could be necessary in order to not disturb you while zapping through channels which can't be descrambled by your smart card. If your choice is Fixed channel: press OK button to display a channel list, select a channel and confirm selection with OK button. If your choice is Last Viewed then receiver will awake with the last watched channel. Dolby ­ the receiver will by-pass AC3 audio for future decoding by Digital Audio Amplifier. 5. 3. 2 TV Setting In this menu, you can configure the TV setting such as HD type, TV type, Aspect Ratio, Screen Control, RGB/YUV, Brightness, Contrast, Saturation. n HD type Use pqtu buttons to select the item and press OK button to display the list of options, use pq buttons to select a video output resolution and press OK button to confirm selection. Tip: n HD type is not selectable if output mode (YUV/RGB) set to RGB. TV Type Use pqtu buttons to select the item and press OK button to display the list of options, use pq buttons to select TV Type and press OK button to confirm selection. If you have changed TV type and Video on screen not appears in 15 seconds ­ press EXIT button 2 times. Such a problem can appear if your TV do not supports video in NTSC format. 13 Tip: n English PART 1 · English Use pqtu buttons to select the item and press OK button to display the list of options, use pq buttons to select Aspect Ratio then press OK button to confirm selection. [. . . ] If the receiver does not work properly after checking it, please contact the dealer. No picture The receiver can't receive the signal Incorrect values of channel parameters. You have switched to a Radio channel The remote control does not work The batteries of the remote control are not inserted or exhausted Remedy Check that the power cord is plugged in to the wall outlet. Check the antenna cable, replace the cable, or connect the cable to the receiver tightly. [. . . ]