User manual STRONG SRT 4356

[. . . ] This receiver is of our latest development; it is designed to be compatible with new technologies by upgrading its software through the satellite and the Internet. It is highly recommended that you read this manual carefully to safely install your receiver to achieve its optimum performance. user Manual: Part 1 Part 2 Part 3 Part 4 Part 5 Part 6 English Deutsch Italiano РуссκИЙ Specifications Warranty Certification 1. 0: Usage This user manual is applicable for Strong SRT 4356 PVR Evolution (Personal Video Recorder) Digital Satellite Receiver and its related accessories. [. . . ] Factory Reset: Be careful when using this function, because it will erase all the data and parameters you may have set earlier to your receiver. Once you have made a Factory Reset you will have to re-install your preferences and re-scan your channels. To reset your receiver to factory default, apply the following steps: 1. Note: Your PIN code will change back to the factory setting "1234". 2 LNB Set-up (Please see inside cover Screen 17) It is recommended that you read the manual and installation instructions of your LNB, your DiSEqC switch, your 0/12V switch and your Positioner before you start setting up your LNB. Check the exact specifications of your LNB through the manufacturers information or your dealer. The Default is set to Universal mode (9750/10600MHz), DiSEqC is not used and the LNB is mounted on a fixed dish. Use the UP/DOWN keys on your remote to select an item and use the LEFT/RIGHT buttons to set up any values. LNB: Up to 16 LNBs are available, select the correct one according to your LNB specifications. in UNI 1-9750/10600 MHz , UNI2-9750/10700MHz , UNI3 9750/10750 MHz LNB Power: Select 13/18V , 13V or 18V for LNB. Select "Oil" if you want to switch the power of the LNB off. lNB Dish: Using the Left/Right buttons , select "Fixed" or "Motorized" (Move) Dish. If you use a motorized dish, read the "Positioner Set-up" (Described in section 5. Tip: If you set "LNB type" to "Universal" (UNII - UNI3), you will not be able to change settings in both the "LNB Power" menu item and the "Switch 22kHz' menu item. If you want to change any of these two settings you must set "LNB type" to zero. If DiSEqC switch is Off, you will not be able to change settings in both the "DiSEqC Input" and "DiSEqC Repeat" menu items. Alternatively if you set LNB Dish to "Moved", the DiSEqC switch menu item is automatically switched to off if your "LNB dish" is set to "fixed" you will be able to select the required DiSEqC level in the DiSEqC switch menu item. Press the Red (Save) button, the Blue (Save &Exit) button to save the setting. Press the Green (Exit) button or Exit button if you don't want to save the setting. 3 Channel Set-up (Please see inside cover Screen 18) The channel set-up is for downloading tile channels available on the satellites. To download channels, please apply the following steps: In this menu, you can edit the satellites name, and edit the transponder of the satellite. You can also display the LNB menu and the Positioner Set-up menu by selecting LNB and Dish Position respectively. [. . . ] Software changeable by Menu screen RGB, CVBS, L, R Output with Volume Control CVBS, L, R In / CVBS, L, R Out RCA Jack Output (Black Jack), 150mA RS-232, Bit Rate: 115200baud 9-pin D-sub type (S/PDIF) MPEG-2 ISO/IEC 13818 Transport Stream Specification MPEG-2 MP@ML Max. 60Mbit/s 4:3, 16:9 25Hz for PAL, 30Hz for NTSC 720x576(PAL), 720x480(NTSC) via OSD MPEG/MusiCam Layer I& II, MP3, AC3 Single channel/Dual channel Joint stereo/Stereo 20-20kHz, <+/-2dB / 60Hz - 18kHz <+/- 0. For your benefit, we recommend that you record your serial number, found on the back of your receiver, and other purchase information on this card. Make a copy of this certificate and keep it with your personal records, along with your proof of purchase. [. . . ]