User manual STRONG SRT 5429

[. . . ] Also, make sure you do not use the unit with a damaged power cord, as this may cause electric shock or fire n n A professional installation is required. If reception is interrupted, contact your authorized local service center 2. 2 Precautions When installing the unit n Install the unit on a level horizontal plane. Unleveled installation may cause damage to the unit The socket-outlet shall be installed near the equipment and shall be easily accessible Do not put heavy items, such as a TV, on top of the unit. That may cause damage to the unit Do not install the unit where: it may be subject to vibrations it is exposed to direct sunlight there is humidity temperature may be too high or too low there is no adequate ventilation n n n n Moving the unit from a cold area to a hot one will cause condensation. [. . . ] If you want to rename selected satellite ­ press Info button LNB Type: Select between Universal / Wide Band / OSC C- Band / C-Band / Ku-Band / Unicable / Standard Sat. Make your selection depending from installed LNB High L. O. : Low L. O. : 22 kHz Tone: On / Off / Auto - Make your selection depending from installed LNB DiSEqC: LNB Power: Positioner: Off / DiSEqC A, B. If you have DiSEqC 1. 0 or Tone Burst switch installed H/V / 14 V / 18 V / Off None / DiSEqC 1. 2 / USALS. If you use antenna mounted on the DiSEqC 1. 2 positioner then select "DiSEqC 1. 2". If your positioner is USALS compatible then select "USALS" Enter the frequency of Local Oscillator for High band. Refer to your LNB manual Enter the frequency of Local Oscillator for Low band. Refer to your LNB manual 12 PART 1 l English 8. 2. 2. 1 DiSEqC 1. 2 positioner setup by a professional. In "Antenna Setup" menu set Positioner to "DiSEqC 1. 2" and press OK button to enter to "Antenna position" menu. n n Use CH p/q to move up and down in the list Use Vol t/u to change the setting Satellite: Transponder: Move: Save position: Select satellite position of which you would like to setup Select reference transponder which should be used for signal quality indication When this item is highlighted press Vol t/u to move dish in East/West direction accordingly Highlight this item and press OK to store current position of the dish for selected satellite. The ¸ symbol shown near menu item once position is stored Reference position: Highlight this item and press OK if you need to turn dish to reference position (0 degree position). Function: Set west limit / Set east limit ­ select it and press OK if you want to store current position of the dish as west / east limit; Disable limit / Enable limit ­ select and press OK to disable / enable limits; Recalculate ­ select and press OK to recalculate positions of all satellites based on adjustment for current satellite; Nudge west / Nudge east ­ select and press OK for fine adjustment of the dish position; Nudge tilt up / Nudge tilt down ­ use this command if your positioner support adjustment of elevation Antenna status: Signal Quality: Show you current status of the antenna (stopped, moving to East/West) Show quality of signal for selected reference transponder. This mode allows you to find all channels, even from new appeared transponders. "TP" ­ this method is to search channels from one transponder. Select the menu language and Logo for Radio channel Menu Language: Available English / Hungarian / Czech / Slovak / Bulgarian / Turkish / German Radio Ch Logo: Enable or disable logo for Radio channels n n n n Use CH p/q to move upwards and downwards in the menus Use Vol t/u to change the values in the alternatives When you have reached the required subject menu, press OK to confirm your selection Press EXIT to go back to the previous mode PART 1 l English 8. 3. 4 Edit Channels Press OK on the `Edit Channel'. TV/Radio Channel Move Channel Favorite Lock Channel Delete Channel Add Channel Edit Name Use EXIT button to toggle between channel lists and function selection. To toggle between TV and Radio lists highlight function and use CH p/q to select list. To return to menu press EXIT button when any function is highlighted. You will be required to confirm or discard changes that you have made. 8. 3. 4. 1 Move channel To move channel highlight icon and press OK. If you want to move group of channels ­ highlight and select with OK button all channels that you want to move. Once you finish selection of channels, select position in the channel list where to move selected channels and press RECALL button. Press EXIT to return to function selection or continue to move other channels if you want. 8. 3. 4. 2 Add to favourite list To add channel to favourite list highlight icon and press OK. Highlight the channel which you want to add to favourite group and press OK. If you wish to remove channel from favourite group select group "[0] ­ unselect". Press EXIT to return to function selection. 8. 3. 4. 3 Lock channel Lock function is designed to give parents possibility to deny access of children to unwanted channels (channels with adult content, for example). If you wish to unlock channel then repeat selection with OK button. [. . . ] Note: We recommend to use different PIN codes for the smart card and for the receiver. Smart Card Pin Code Change: Available Program Providers: Enter Old Pin / Enter New Pin / Confirm New Pin. Information about program providers. PART 1 l English 8. 3. 6 About Press OK on the `About'. To download latest software version highlight "Update" and press OK. [. . . ]