User manual SUPERMICRO H8QME-2

[. . . ] This product, including software and documentation, is the property of Supermicro and/or its licensors, and is supplied only under a license. Any use or reproduction of this product is not allowed, except as expressly permitted by the terms of said license. BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL, SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SHALL NOT HAVE LIABILITY FOR ANY HARDWARE, SOFTWARE, OR DATA STORED OR USED WITH THE PRODUCT, INCLUDING THE COSTS OF REPAIRING, REPLACING, INTEGRATING, INSTALLING OR RECOVERING SUCH HARDWARE, SOFTWARE, OR DATA. [. . . ] Note 2: Be sure to remove the onboard CMOS Battery before you short JBT1 to clear CMOS. Watch Dog Enable/Disable Watch Dog (JWD1) is a system monitor that will reboot the system when a software application hangs. Close pins 2-3 to generate a non-maskable interrupt signal for the application that hangs. Watch Dog must also be enabled in the BIOS. COM2 JUIDB USB2/3 VGA USB0/1 COM1 USB6 Watch Dog Jumper Settings Jumper Setting Pins 1-2 Pins 2-3 Open Definition Reset (default) NMI Disabled A. Watch Dog Enable LED3 LEDM1 JIPMB1 BMC CTRL LAN CTRL BMC FAN8 JPG1 JPB1 FAN7 LAN2 LAN1 IPMI_LAN SP1 LAN CTRL JD1 JI2C1 JI2C2 CLK CTRL JPL1 JVRM_I2C1 JVRM_I2C2 JTPM1 CPU1 SLOT3 PCI-E 3. 0 X8 CPU1 SLOT5 PCI-E 3. 0 X8 PCH CPU1 SLOT4 PCI-E 3. 0 X8 CPU2 SLOT6 PCI-E 3. 0 X16 CPU2 SLOT7 PCI-E 3. 0 X8 JBT1 X9DRD-iF Rev. 1. 10 G1 H1 F1 JPW4 E1 A CPU2 JPME2 JPME1 JWD1 I-SATA0 I-SATA2 I-SATA4 SCU0 SCU2 USB4/5 USB8/9 T-SGPIO2 T-SGPIO1JSTBY1 JL1 FAN6 S-SGPIO1 FAN4 JVR1 JRK1 B I-SATA1 I-SATA3 I-SATA5 SCU1 SCU3 FAN5 JSD1 C1 D1 BIOS B1 A1 CPU1 JVR2 JPW3 JBAT1 JOH1 + JPW1 JPW2 :OH LED LED2 JPW5 FP CTRL JPI2C1 FAN1 FAN2 FAN3 2-36 JF1 Chapter 2: Installation VGA Enable Jumper JPG1 allows the user to enable the onboard VGA connector. See the table on the right for jumper settings. VGA Enable Jumper Settings Jumper Setting 1-2 2-3 Definition Enabled (Default) Disabled BMC Enable Jumper JPB1 allows you to enable the embedded WPCM 450 BMC (Baseboard Management) Controller to provide IPMI 2. 0/KVM support on the motherboard. See the table on the right for jumper settings. BMC Enable Jumper Settings Jumper Setting Pins 1-2 Pins 2-3 Definition BMC Enable (Default) Normal COM2 JUIDB USB2/3 VGA JIPMB1 USB0/1 COM1 USB6 A. BMC Enabled LED3 LEDM1 BMC CTRL LAN CTRL BMC FAN8 JPG1 JPB1 FAN7 A LAN2 LAN1 IPMI_LAN SP1 JD1 B LAN CTRL JI2C1 JI2C2 CLK CTRL JPL1 JVRM_I2C1 JVRM_I2C2 JTPM1 CPU1 SLOT3 PCI-E 3. 0 X8 CPU1 SLOT5 PCI-E 3. 0 X8 PCH CPU1 SLOT4 PCI-E 3. 0 X8 CPU2 SLOT6 PCI-E 3. 0 X16 CPU2 SLOT7 PCI-E 3. 0 X8 X9DRD-iF Rev. 1. 10 G1 H1 F1 JPW4 E1 JBT1 CPU2 JPME2 JPME1 JWD1 JSD1 JRK1 BIOS B1 A1 I-SATA0 I-SATA2 I-SATA4 SCU0 SCU2 USB4/5 USB8/9 T-SGPIO1JSTBY1 JL1 FAN6 I-SATA1 C1 D1 I-SATA3 I-SATA5 SCU1 SCU3 T-SGPIO2 S-SGPIO1 CPU1 JVR2 JPW3 JBAT1 JOH1 + JPW1 JPW2 :OH LED LED2 JPW5 FAN4 JVR1 FAN1 FAN5 FAN2 FAN3 FP CTRL JF1 JPI2C1 2-37 X9DRD-iF/LF Motherboard User’s Manual Management Engine (ME) Recovery Use Jumper JPME1 to select ME Firmware Recovery mode, which will limit resource allocation for essential system operation only in order to maintain normal power operation and management. In the single operation mode, online upgrade will be available via Recovery mode. See the table on the right for pin definitions. Serial ATA/SCU Pin Definitions Pin# 1 2 3 4 5 6 7 Definition Ground TX_P TX_N Ground RX_N RX_P Ground Note 1: X9DRD-LF only has I-SATA0 and I-SATA1. Note 2: For more information on SATA HostRAID configuration, please refer to the Intel SATA HostRAID User's Guide posted on our website @ http://www. supermicro. com. . A. I-SATA0 COM1 USB6 COM2 JUIDB USB2/3 VGA USB0/1 LED3 LEDM1 BMC CTRL LAN CTRL B. SCU3 JIPMB1 BMC FAN8 JPG1 JPB1 FAN7 LAN2 LAN1 IPMI_LAN SP1 LAN CTRL JD1 JI2C1 JI2C2 CLK CTRL JPL1 JVRM_I2C1 JVRM_I2C2 JTPM1 CPU1 SLOT3 PCI-E 3. 0 X8 CPU1 SLOT5 PCI-E 3. 0 X8 PCH CPU1 SLOT4 PCI-E 3. 0 X8 CPU2 SLOT6 PCI-E 3. 0 X16 CPU2 SLOT7 PCI-E 3. 0 X8 JBT1 X9DRD-iF Rev. 1. 10 G1 H1 F1 JPW4 E1 CPU2 JPME2 JPME1 JWD1 JSD1 JRK1 A B C1 D1 BIOS B1 A1 I-SATA0 I-SATA2 I-SATA4 SCU0 SCU2 USB4/5 USB8/9 T-SGPIO1JSTBY1 JL1 FAN6 I-SATA1 I-SATA3 C E D F CPU1 I-SATA5 G H JVR2 SCU1 I J SCU3 T-SGPIO2 S-SGPIO1 JPW3 JBAT1 JOH1 + JPW1 JPW2 :OH LED LED2 JPW5 FAN4 JVR1 FP CTRL JPI2C1 FAN1 FAN5 FAN2 FAN3 JF1 2-42 Chapter 3: Troubleshooting Chapter 3 Troubleshooting 3-1 Troubleshooting Procedures Use the following procedures to troubleshoot your system. If you have followed all of the procedures below and still need assistance, refer to the ‘Technical Support Procedures’ and/or ‘Returning Merchandise for Service’ section(s) in this chapter. Note: Always disconnect the power cord before adding, changing or installing any hardware components. Before Power On 1. Make sure that there are no short circuits between the motherboard and chassis. 2. Disconnect all ribbon/wire cables from the motherboard, including those for the keyboard and mouse. 4. Install CPU 1 first (making sure it is fully seated) and connect the front panel connectors to the motherboard. No Power 1. Make sure that no short circuits between the motherboard and the chassis. 2. Make sure that the ATX power connectors are properly connected 3. Check that the 115V/230V switch on the power supply is properly set, if available. 4. Turn the power switch on and off to test the system, if applicable. [. . . ] Boot Override This feature allows the user to enter a new setting to overwrite the original setting that was saved for the following devices: • GE Slot IBA • Built-in EFI Shell: UEFI: 4-31 X9DRD-iF/LF Motherboard User’s Manual Notes 4-32 Appendix A: BIOS POST Error Codes Appendix A BIOS Error Beep Codes During the POST (Power-On Self-Test) routines, which are performed at each system boot, errors may occur. Non-fatal errors are those which, in most cases, allow the system to continue to boot. Fatal errors will not allow the system to continue with bootup procedure. If a fatal error occurs, you should consult with your system manufacturer for possible repairs. [. . . ]