User manual TACWISE 191EL PRO
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual TACWISE 191EL PRO. We hope that this TACWISE 191EL PRO user guide will be useful to you.
Manual abstract: user guide TACWISE 191EL PRO
Detailed instructions for use are in the User's Guide.
[. . . ] ENGINE IDENTIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ENGINE CARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AIR CLEANERS, CARBURETORS, GOVERNORS AND LINKAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AIR CLEANERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use a "Vee" block and the flat side of a grindstone to grind valve clearance. The end of the stem must be flat and true or abnormal wear will occur.
EXHAUST VALVE SEAT IN HEAD
INTAKE
VALVE GUIDE DIMENSIONAL CHECK. Check dimensions per specification requirements, determine if valve guide clearance is beyond acceptable tolerance. If valve guide clearance is worn beyond tolerance, ream valve guide oversize and install 1/32'' (. 787 mm) oversize valve, or replace valve guides.
29
THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH IF NOT FOLLOWED COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF AND OTHERS. VALVE GUIDE REMOVAL AND INSTALLATION INSTRUCTION FOR VALVE-IN-HEAD ENGINES. Submerge the head in a pan of oil so that both guides are covered with oil. When the oil begins to smoke, remove the head from the pan of oil with a pair of pliers. Place head on the bed of an arbor press on parallels with the snap rings on the long ends of the guides facing down. Use a 1/2''(25. 4 mm) diameter, 6'' (152 mm) driftpunch and the arbor press to push valve guides out of the head.
GUIDES HEAD OIL
INSTALLING NEW GUIDES NOTE For easy installation, the replacement guides should be placed in the freezer compartment of a refrigerator or on ice for no less than 30 minutes prior to installation. Submerge head with guides removed in a container of oil so that both guide bores are covered with oil. When the oil begins to smoke, remove the head from the pan with a pair of pliers. See Specifications.
TOP PISTON LAND CLEARANCE PISTON 1st COMPRESSION RING
CYLINDER WALL
SIDE CLEARANCE
3rd OIL CONTROL RING
PISTON DIAMETER MEASUREMENT. This is a cam ground piston and the diameter will not be the same when checked at another point. Pistons and rings may be available in either . 010'' (. 254 mm), . 020'' (. 508 mm), . 030'' (. 762 mm) and . 040'' (1. 016 mm) oversize.
RING AND WRIST PIN ASSEMBLY. Stagger the piston ring gaps 90° apart when installing piston and ring assembly in cylinder. The wrist pin is a palm press fit (pressed in by hand with some resistance). Replace piston and wrist pin if loose.
RING GAPS
CHECK PISTON DIAMETER AT THIS POINT
RING END GAP MEASUREMENT. Before installing the rings, insert each ring into the cylinder bore to check the end gap. This gap check should be made in a worn cylinder, a reconditioned cylinder and a new cylinder. An inverted piston should be used to push the ring into the cylinder to a point that would be the center of ring travel. Insert the piston ring into the cylinder and place the top side of the piston on the ring to position the ring squarely in the bore; remove piston. Measure the end gap by inserting a feeler gauge between the ring ends. [. . . ] Valve Face Angle Valve Face Width 45° . 089 . 099 . 06 1. 885 . 312 . 313 . 344 . 345 1. 3750 1. 3755 1. 3761 1. 1865 1. 1870 None 3. 308 3. 310 . 6873 . 6875 . 0950 . 0960 . 1800 . 1900 . 0025 . 0030 . 010 . 020 . 0305 . 0335 . 003 . 6235 . 6240 1. 3045 1. 3085 . 006 . 010
191EL PRO Metric 45° 2. 261 2. 515 1. 524 47. 879 7. 925 7. 950 8. 738 8. 763 34. 925 34. 938 44. 097 30. 137 30. 150 U. S. 45o . 089 . 099 . 06 1. 885 . 312 . 313 . 344 . 345 1. 3750 1. 3755 1. 3761 1. 1865 1. 1870 None 84. 023 84. 074 17. 457 17. 463 2. 41 2. 438 4. 572 4. 826 . 635 . 076 . 254 . 508 . 775 . 851 . 076 15. 837 15. 850 33. 134 33. 236 . 152 . 254 3. 308 3. 310 . 6873 . 6875 . 0950 . 0960 . 1800 . 1900 . 0025 . 0030 . 010 . 020 . 0305 . 0335 . 003 . 6235 . 6240 1. 3045 1. 3085
VH100 Metric 45o 2. 261 2. 515 1. 524 47. 879 7. 925 7. 950 8. 738 8. 763 34. 925 34. 938 44. 097 30. 137 30. 150
Valve Lip Width Valve Spring Free Length Valve Guides STD Diameter
Valve Guides Over-Size Dimensions
Diameter Crankshaft Conn. for Roller Bearings
Crankshaft End Play Piston Diameter
84. 023 84. 074 17. 457 17. 463 2. 41 2. 438 4. 572 4. 826 . 635 . 076 . 254 . 508 . 775 . 851 . 076 15. 837 15. 850 33. 134 33. 236 . 152 . 254
Piston Pin Diameter
Width Comp. Ring Groove
Width Oil Ring Groove
Side Clearance Ring Groove
Ring End Gap
Top Piston Land Clearance
Piston Skirt Clearance Camshaft Bearing Diameter
Cam Lobe Diameter Nose to Heel
Magneto Air Gap
. 006 . 010 Solid State
NOTE: All dimensions are in inches and millimeters unless noted.
69
SECTION 2. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE TACWISE 191EL PRO
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual TACWISE 191EL PRO will begin.