User manual TEFAL FV4270 ULTRAGLISS EASYCORD

[. . . ] Remove any labels from the soleplate before heating up the iron (depending on model). ULTRAGLIDE easycord 7 5 4 3 2 1 6 8 9 · Before using your iron with the steam function for the first time, we recommend that you operate it in a horizontal position for a few moments, away from your linen, i. e. · During the first few uses, a harmless odour and smoke may be given off. This is normal with no effect on the use of the iron and will disappear quickly. What water to use ? · Your appliance has been designed to function with untreated tap water. [. . . ] Any commercial use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no responsibility and the guarantee will not apply. Using the Easycord system fig 1 fig 2 · Your iron is equipped with the Easycord system to prevent the cord trailing across the laundry and creasing it during ironing. · Press the button located on the base (fig. 4) and the Easycord system is automatically in use. You can now plug in your appliance and begin ironing. Always use the Easycord system for enhanced comfort of use. Click! 5 · Use Adjust the temperature and the steam fig 3 fig 4 · Select the temperature (see table below) setting the thermostat facing the indicator (fig. 5). · Set the steam control (fig. 7) to the desired position, consulting the table below. POSITION MAX MATERIAL LINEN OF STEAM SETTING THERMOSTAT CURSOR POSITION COTTON WOOL SILK SYNTHETICS (Polyester, Acetat, Acryl, Polyamide) ··· ·· · fig 5 fig 6 = STEAM ZONE · Your iron heats up quickly : so begin by ironing fabrics that are ironed at low temperatures first, then go on to those requiring a higher temperature. It is normal for the indicator light to switch on and off during ironing In order to avoid water dripping from the iron onto the linen: - turn off the steam when ironing silk or synthetic fabrics. If you turn down the thermostat, wait until the thermostat light comes back on before beginning to iron again or it will be too hot. When ironing fabrics with mixed fibres, set the ironing temperature for the most delicate fibre. For delicate fabrics we recommend testing the fabric first on an inconspicuous place eg (inside the hem). If you want to dry iron, set the Steam control to . your iron for 2 minutes on its heel to dry the soleplate. To slow down scaling and prolong the life of your iron, carry out the self-cleaning operation once a month or more frequently in a hard water area. Cleaning the soleplate · Unplug the iron, and when the soleplate is just warm, wipe it with a soft cloth. Never use abrasive or aggressive products. 7 · If there is a problem PROBLEM POSSIBLE CAUSE SOLUTION Position the thermostat in the steam range (from ·· to MAX). Water drips from the The chosen temperature is too holes in the soleplate. You have stored the iron horizontally, without emptying it and without setting it to . Brown streaks come You are using chemical through the holes in descaling agents. type of water. Obtain more steam fig 7 fig 9 (according to model) now and again to remove stubborn creases · Press the boost of steam button (fig. 8). Wait a few seconds between each shot before pressing the button again. Spray Function · Whether steam or dry ironing, you are able to use the Spray button dampen laundry to remove stubborn creases. (fig. 9) to Vertical steam ironing (according to model) Ideal for removing creases in suits, jackets, skirts, curtains, etc. : · Hang the garment on a hanger and hold the fabric slightly taut with one hand. · Press the boost of steam button button repeatedly (fig. 8) moving the iron from top to bottom (fig. 10). [. . . ] · Place your iron on its heel, set the thermostat dial to MAX, plug in your iron and wait for the indicator light to go out. · Press the self-clean ejection button (fig. 14a) and remove the anti-calc valve (fig. 14b). · Gently shake the iron over the sink until some of the water (along with impurities) runs out through the soleplate. [. . . ]