User manual TOYOTA SUPER JEANS 26

[. . . ] SP200 Series HOME-USE SEWING MACHINE •• Read this manual carefully before use and always follow the instructions. •• Keep the manual in a convenient place for easy reference. •• If you give the sewing machine to someone else, also give them this instruction manual. INSTRUCTION MANUAL Contents 1 Before use (Be sure to read this section before use) •• •• •• •• •• •• Important safety instructions. 3 How to change the power plug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Loosely hold the upper thread with your left hand, and then turn the handwheel towards yourself one full turn. Do not pull the thread taut. 2 Lightly pull the upper thread with your left hand to pull up the lower thread. Pull out the lower thread to the front. Align both threads, pass them through the groove (arrow) and under the presser foot, and then pull out about 15 cm of thread to the rear. Presser foot 15 cm 22 Application of each stitch pattern Caution Before turning the pattern selection dial, use the main power switch to turn off the sewing machine. Not doing so could cause an injury. Do not turn the pattern selection dial while the needle is lowered. Turn the handwheel towards yourself to raise the needle to its highest position; otherwise, the pattern and stitch length may not be correctly adjusted. 2 Sewing preparations „„When sewing patterns 1 to 15 The length becomes longer Mark above dial The length becomes shorter 1 2 Turn the dial until the desired pattern aligns with the mark above the dial. Turn the stitch length dial until the desired stitch length aligns with the mark above the dial. ** The stitch length can be set between 0 and 4. Since the recommended range differs depending on the pattern, refer to the following table. Pattern selection dial No. Application Stitch length dial (recommended Presser foot setting) 0-4 (0. 4~1) Buttonhole foot Pattern selection dial Application Mending stitch Thin fabric overcasting Decorative stitch Overcasting Stitch length dial Pattern selection dial No. 10 Stitch length dial (recommended Presser foot setting) 0-4 (1~2) 0-4 (1~2) 0-4 (1~2) 0-4 (1~2) 0-4 (0. 5~2) 0-4 (1~4) 0-4 (1~4) Overcasting foot * Zigzag sewing foot Buttonhole 5 Straight stitch (left side) Straight stitch (center) Zipper insertion 0-4 (1~4) 0-4 (1~4) 0-4 (2~4) Zigzag sewing foot 11 12 Decorative stitch Zipper foot 13 Decorative stitch Blind stitch foot * 14 6 7 Blind hem stitch 0-4 (1~2) Zigzag stitch (medium) Zigzag stitch (large) Overcasting 8 Decorative stitch 0-4 (1~4) Zigzag sewing foot 15 Overcasting 9 Stretch fabric blind hem stitch 0-4 (1~2) Blind stitch foot * ** Included only with model XXX34C/SuperJ34. The zigzag sewing foot can also be used for 7, 9, 15. 23 Caution Before turning the pattern selection dial, use the main power switch to turn off the sewing machine. Not doing so could cause an injury. „„When sewing patterns A to K 1 2 Turn the dial until the desired pattern aligns with the mark above the dial. Turn the stitch length dial aligns with the mark until above the dial. ** The stitch length is fixed at 3 mm and cannot be adjusted. Mark above dial Stitch length dial Mark above dial Pattern selection dial Turn to the left Pattern selection dial No. A Application Stitch length dial (recommended Presser foot setting) Pattern selection dial No. G Application Stitch length dial (recommended Presser foot setting) Reinforced straight stitch (left side) Reinforced straight stitch (center) Decorative stitch Overlock B H Decorative stitch Overlock Zigzag sewing foot Decorative stitch C Decorative stitch Double overlock I Zigzag sewing foot J D Decorative stitch Reinforced zigzag stitch (medium) Reinforced zigzag stitch (large) E Decorative stitch K F Decorative stitch 24 Caution Do not turn the pattern selection dial while the needle is lowered. Doing so could break the needle and cause an injury. „„When sewing patterns L to S ** Stitches L through S can be sewn only with model XXX34C/SuperJ34. 2 Sewing preparations 1 2 Turn the dial until the desired pattern aligns with the mark above the dial. Turn the stitch length dial until aligns with the mark above the dial. ** The stitch length is fixed at 3 mm and cannot be adjusted. Mark above dial Stitch length dial Pattern selection dial Mark above dial Turn to the left Pattern selection dial No. L Application Stitch length dial (recommended setting) Presser foot Pattern selection dial No. R Application Stitch length dial (recommended setting) Presser foot Decorative stitch Decorative stitch Zigzag sewing foot M Decorative stitch N Fagoting O Appliqué P Appliqué Q Decorative stitch Zigzag sewing foot S Decorative stitch 25 Changing the presser foot Caution Before changing the presser foot, use the main power switch to turn off the sewing machine. Not doing so could cause an injury. zz Removal 1 Raise the presser foot lever. 2 Turn the handwheel towards yourself to raise the needle. Handwheel Presser foot lever Press the presser foot holder lever in the direction of the arrow to release the presser foot. Presser foot holder lever Presser foot 26 zz Installation 1 Position the presser foot pin directly below the groove in the presser foot holder. Presser foot holder 2 Groove Sewing preparations Presser foot pin 2 Lower the presser foot lever to secure the presser foot. Presser foot lever Tip In order to avoid losing the presser foot, we recommend storing the machine when it is not being used with the needle and the presser foot lowered. 27 Changing the needle Caution Before changing the needle, use the main power switch to turn off the sewing machine. Not doing so could cause an injury. 1 2 Turn the handwheel towards yourself to raise the point of the needle higher than the needle plate. Hold the needle in one hand, loosen the needle clamp screw with the screw driver for the needle plate, and remove the needle. Face the flat surface of the needle to the rear and insert until it makes contact with the pin. Firmly tighten the needle clamp screw with the screw driver for the needle plate. Pin Screw driver for the needle plate Needle clamp screw Flat surface zz Correct needle selection Good needle If a faulty needle is used, not only could it impair the sewing performance, but it could also damage the needle plate or hook, or break the needle. ** Incorrect stitching or thread breaking, try replacing the needle. ÍFaulty needle The entire needle is bent 28 The point of the needle is crushed / worn away The point of the needle is bent Relationship between the needle, thread and fabric, and adjusting the thread tension The quality of the sewing finish will improve if the needle and thread are changed to match the type of fabric. zz For XXX26C/XXX34C Reference thread tension -3 -1 +1 Normal fabrics No. 50 Curtains Denim Quilting Fleece Tweed Felt, etc. 2 Sewing preparations Thread Fabric Normal front cloth Broad Soft denim Satin Pile Gingham, etc. -2 -1 +2 +1 +2 +3 +4 Upper thread tension dial -1 ~ -3 +1 ~ +3 zzFor SuperJ26/34 -1 ~ -3 -1 ~ +3 • Use a ball point needle for the sewing alignment of stretch fabric. [. . . ] Not doing so could cause a burn or electric shock. 8 1 Loosen the screw with a + screw driver of your own, and take off the face cover in the direction of the arrow. Screw Face cover 8 2 Turn the light bulb counterclockwise as the arrow in the diagram and remove. Turn the new light bulb clockwise to install. Always reinstall the face cover after replacing the light bulb. 48 Servicing double-insulated products (230V-240V) In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means are provided on a double-insulated product nor should a means for grounding be added to the product. Servicing a double-insulated product requires extreme care and should only be done by qualified service personnel with knowledge of the system under his or her responsibility. [. . . ]