User manual TP-LINK TD-W8920G

[. . . ] TD-W8920G 108M Wireless ADSL2+ Router User Guide TD-W8920G 108M Wireless ADSL2+ Router Rev: 1. 0. 2 1910010014 TD-W8920G 108M Wireless ADSL2+ Router User Guide COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO. , LTD. http://www. tp-link. com TD-W8920G 108M Wireless ADSL2+ Router User Guide FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. [. . . ] The IP address filtering includes Outgoing and Incoming, the detailed descriptions are provided below. IP Filtering - Outgoing Choose "Advanced Setup" "Security" "IP Filtering" "Outgoing", you can configure Outgoing Filtering rules on the screen (shown in Figure 4-24). The Outgoing IP Filtering feature allows you to control some IP traffic from LAN to access to some specifically addresses. By default, all outgoing IP traffic from LAN is allowed, but some IP traffic can be BLOCKED by setting up filters. Figure 4-24 Setup an Outgoing IP Filtering rule: 1. Click the Add button (pop-up Figure 4-24), then you will set the new rule in the next screen (shown in Figure 4-25). 36 TD-W8920G 108M Wireless ADSL2+ Router User Guide Figure 4-25 2. Enter the Filter name for the rule, it is exclusive and must be filled. Select the protocol: TCP/UDP, TCP, UDP or ICMP in the drop-down list for the connection between the Source IP address and Destination IP address. Enter a Source IP Address in dotted-decimal notation format and then type the Source Subnet Mask and Source Port (port or port: port) in the text boxes separately. Enter a Destination IP Address in dotted-decimal notation format and then type the Destination Subnet Mask and Destination Port (port or port: port) in the text boxes separately. Note: When you add an Outgoing IP Filtering entry, you must configure at least one condition on the screen above except the Filter name. If you leave the Protocol blank, it means that the rule is effective to all protocols, if you leave the Source IP Address and/or Destination IP Address blank, it suggests that all Source IP Addresses and/or Destination IP Addresses are controlled by the rule, if you leave the Source Port and/or Destination Port blank, it suggests that all Source Ports and/or Destination Ports are controlled by the rule. IP Filtering - Incoming Choose "Advanced Setup" "Security" "IP Filtering" "Incoming", you can configure Incoming Filtering rules on the screen (shown in Figure 4-26). The Incoming IP Filtering feature allows some IP traffic from WAN to access some local addresses. By default, all incoming IP traffic from the WAN is blocked when the firewall is enabled. However, some IP traffic can be ACCEPTED by setting up filters. 6. 37 TD-W8920G 108M Wireless ADSL2+ Router User Guide Figure 4-26 Setup an Incoming IP Filtering rule: 1. Click the Add button (pop-up Figure 4-26), and then you will set the new rule in the next screen (shown in Figure 4-27). Figure 4-27 2. Enter the Filter name for the rule, it is exclusive and must be filled in. Select Protocol in the drop-down list, enter Source IP address, Source Subnet Mask, Source Port, Destination IP address, Destination Subnet Mask, and Destination Port for the rule. Select at least one WAN interfaces displayed below to apply this rule. 5. 38 TD-W8920G Note: 108M Wireless ADSL2+ Router User Guide When you add a Incoming IP Filtering entry, you must configure at least one condition on the screen above except the Filter name. If you leave Protocol blank, it means that the rule is effective to all protocols, if you leave the Source IP address and/or Destination IP address blank, it suggests that all Source IP addresses and/or Destination IP addresses are controlled by the rule, if you leave the Source Port and/or Destination Port blank, it suggests that all Source Ports and/or Destination Ports are controlled by the rule. MAC Filtering Choose "Advanced Setup" "Security" "MAC Filtering", you can configure MAC Filtering rules on the screen (shown in Figure 4-28). [. . . ] The two processes may be on the same system, or they may be on different systems with a network connecting them. By using RPC, programmers of distributed applications avoid the details of the interface with the network. The transport independence of RPC isolates the application from the physical and logical elements of the data communications mechanism and allows the application to use a variety of transports. Server - Any computer whose function in a network is to provide user access to files, printing, communications, and other services. [. . . ]