User manual TP-LINK TL-SL2452WEB

[. . . ] User's Guide TL-SG2109WEB 9-port Gigabit Web Smart Switch TL-SL2210WEB 8+2G Gigabit Web Smart Switch TL-SL2218WEB 16+2G Gigabit Web Smart Switch TL- SL2428WEB 24+4G Gigabit Web Smart Switch TL-SL2452WEB 48+4G Gigabit Web Smart Switch COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK Technologies Co. , Ltd. All rights reserved. FCC STATEMENT This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC Rules. [. . . ] Hardware Version: Displays the installed device hardware version number. System Location: Defines the location where the system is currently running. Contact Information: Defines the contact information of switch manager. Run time: Shows the run time since last startup. 5. 3. 1. 2 File Transfer This page contains the following fields: Figure 5-17 File Transfer 33 TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide Transfer Type: Lists three types of file transfer supported by the switch. File Name: Identifies the file to be loaded or to be backed up on TFTP server. Further explanation File transfer types: System Upgrading: Means downloading the executable file from TFTP server to switch and upgrading the system. Configuration Backup: Means backing up the current configuration of the switch to TFTP server. Configuration Loading: Means downloading the configuration from TFTP server to the switch and update it. Notice: 1) Please make sure the target file exits on TFTP server before downloading. 3) Breaks should be avoided during file transfer; otherwise, the switch may get damaged. 5. 3. 1. 3 Reboot & Reset This page is showed as below. Figure 5-18 Reboot & Reset 34 TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide A prompt will display if a button is pressed. For example, if the button "Softreset" is pressed, a message box will be activated as showed in figure 5-19. Figure 5-19 Message Box 5. 3. 1. 4 User This page provides the interface of configuring username and password. Figure 5-20 User Configuration You are kindly suggested to retype the new password in "Confirm new password" box instead of copying in order to avoid typing mistakes. Notice: 1) Only letters, numbers and punctuations can be input into username and password field, the other characters are considered illegal. 2) The initial username and password is supervisor/supervisor. 35 TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide 5. 3. 2 Port Setting 5. 3. 2. 1 Port Parameter This page contains the following fields: Figure 5-21 Port Parameter Port Status: Indicates whether the port is operational or non-operational. " Enable" Indicates the port is operational and "Disable" Indicates the port is non-operational. If a port is unused for a long time, it can be set it to be non-operational to cut down energy costs. Notice: You can't manage the switch via the port, which is non-operational, please set the value of the management port to "enable". Port Security: "Enable" Indicates the port will not learn new MAC address and only transmit the frames from the MAC address it has learned. " Disable" Indicates it will learn new MAC address. 36 TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide Notice: If you haven't set the static MAC address, you can't enable all of the port security, which will result in an inability to manage the switch. Flow Control: Indicates whether the flow control is enabled or disabled. Duplex Mode: Possible filed values are Auto, 10M HD, 10M FD, 100M HD, 100M FD and 1000M FD (Giga port support), "HD" stands for halfduplex and "FD" stands for full-duplex. Further explanation: 1) By operating on fields in the All Ports line expediently, you can set the values of all ports in the corresponding field. 2) Parameters of Trunk member ports are configured with default value (see the Appendix B table) and cannot be configured here (see port 5 and 6 in the figure for example). For SFP, the Duplex Mode is set to "1000M FD" and cannot be modified. 5. 3. 2. 2 Port Statistic This page displays the port statistic, it contains the following entries: Figure 5-22 Port Statistic 37 TL-SG2109WEB/TL-SL2210WEB/TL-SL2218WEB/TL-SL2428WEB/TL-SL2452WEB Web Smart Gigabit Switch Family User's Guide Tx Collisions: The number of collision events seen by the MAC. Tx Ucast: The number of frames sent that have a unicast destination MAC address. Tx Mcast: The number of frames sent that have a multicast destination MAC address. Tx Bcast: The number of frames sent that have a broadcast destination MAC address. Rx Ucast: The number of frames received that have a unicast destination MAC address. [. . . ] Clean Up: Clean up the Trunk member list. Notice: 1) Each Trunk should contains 2 to 4 ports (If a Trunk is submitted with 0 member port, it indicates to delete the Trunk). 2) SFP and 1000M port in TL-SL2210WEB/TL-SL2218WEB/TLSL2428WEB/TL-SL2452WEB, is not able to be the Trunk member. 3) Trunks cannot be set if the switch is in MTU VLAN mode. 5. 3. 6 Priority Setting Priority setting contains four topics: priority mode, port-based priority, port default priority and 802. 1p priority. Because dynamic menu is adopted, only the pages corresponding to current priority mode are revealed. [. . . ]