User manual TYAN NETSCALIBUR

[. . . ] 13 Install Dial-Up Networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Install Remote Access Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Install Internet Explorer and ISDN Diagnostic Tool . . . . . . . . . . . . . . . . . . . . . . . . 17 Windows NT 3. 51 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Normally, this is a good indication that the Netscalibur card, cable, and the ISDN lines are functioning properly. However, it does not guarantee that the SPID and phone numbers are entered correctly. 6 L1, L2, and L3 lights turn red: This means that the driver is not loaded. For Windows 95 users, first check the Netscalibur's network properties in the Device Manager for resources conflicts. An interrupt or IO address conflict will prevent the driver from loading. You can access the Device Manager by moving the mouse cursor to My Computer follow by clicking on the right mouse button to bring out the properties sheet. Afterwards, click on properties to go to System Properties and then select Device Manager folder. Go down to network adapters and double-click on Netscalibur ISDN ISA-PnP to check Resources for conflicts. For Windows NT users, you should bring up the Windows NT diagnostic in Administrative tools to check for resource conflicts. Check the ISDN RJ-45 to the phone jack and make sure they are properly inserted. L1 lights turn green but L2 and L3 remain red: This is normal if the phone company uses Point-to-Point protocol. Otherwise, it means that the driver is loaded but the switch type, SPID numbers, or the phone numbers for ISDN are incorrect. First check the switch type, SPID numbers, and phone numbers in the Start -> Programs -> Accessories -> ISDN tools -> ISDN Configuration Wizard. Make sure you enter the correct SPID numbers, phone numbers, and switch type. The B Channel Activity light will turn green only after the connection has been established. If Ch1 turns green but Ch2 remains red, it means that only channel 1 is connected. The ISDN diagnostic tool does not work under Windows NT 3. 51. It will work under Windows 95 and Windows 4. 0. 7 95 1. Power off the system and insert the Netscalibur into an empty 16-bit ISA slot and remove other modem cards from the system. You must install the ISDN accelerator pack v1. 1 or above before installing Netscalibur's ISDN driver. Therefore, before you install the Microsoft ISDN Accelerator Pack from the Netscalibur Wizard CD, choose "Do not install a driver (Windows will not prompt you again)" when Windows 95 detects the Netscalibur or choose "Cancel" if you have Windows 95 OEM services release 2 . 2. If you accidentally select "Disk provided by manufacturer. " then you should do an uninstall as described in page 6 before continuing with the setup in step 12. 3. The setup program needs to modify the registry data and copy files to your hard disk. Scanning the hard disk for corrupted files will enable the setup program to copy drivers correctly to the hard disk. The ScanDisk program is located in Start -> Programs -> Accessories -> System Tools. 8 4. The Netscalibur Wizard should auto-start or you can double click on the Netscalibur CD-ROM icon to launch the Netscalibur Wizard. If your CD-ROM drive does not perform auto-run or double-clicking the Netscalibur icon does not bring up the Netscalibur Wizard, then you can run the setup program by selecting Open from the file menu. [. . . ] Otherwise, click on OK to close the network settings window and restart the system. 19 8 If you do not have a network card installed in the system, then you need to do this extra step. After configuring the Remote Access Services, click OK to save the network settings and to close the network window. Instead, re-open the Network applet and select Yes when Windows NT prompts you to install a network card. Afterwards, select Do_Not_Detect and then click on the Remote button to install additional networking components. [. . . ]