User manual UNIVERSAL REMOTE CONTROL 10IN1

[. . . ] *Note : If the 3-digit code number you just entered is the correct number, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off. STEP4 Test functions. Programming Channel Control You can program the channel controls (Channel Up, Channel Down, Last and Numbers) from one Component to operate in another Component mode. Default channel control settings on the remote control are as follows: CBL : CBL DVD : DVD T V : CBL AUD : AUD AUX : AUX 10IN1 Cable Remote Control UR5U-9000L & UR5U-9020L 2 Replacing Batteries Before you program or operate the remote control, you must install two new AA alkaline batteries. [. . . ] STEP2 Check battery polarity carefully, and install the batteries as shown in the illustration below. Pre-Programmed 3-Digit Code Method STEP1 Turn on the Component you want to program (TV, AUD, DVD or AUX). STEP2 Press the [COMPONENT] button (TV, AUD, DVD or AUX) to be programmed and [OK/SEL] button simultaneously for 3 seconds. The Component LED light will turn on for 30 seconds indicating the unit is ready to be programmed. STEP3 Point the remote control toward the Component and enter the 3-digit code number assigned to your brand. *Note : If the 3-digit code number you just entered is correct, the Component will turn Off. If it did not turn Off, continue entering code numbers listed for that brand until the Component turns Off. STEP4 After you've entered the correct code number and the Component has turned Off, press the [POWER] button to turn the Component back On. Now it is time to test the VOLUME and MUTE buttons for the TV (or PLAY and STOP buttons for DVD) to make sure they all work. If any of the functions do not work as they should, repeat from STEP 3 using the next 3-digit code number listed for that brand until you find the best Component code. STEP2 Press the [MACRO] button and [OK/SEL] button simultaneously for 3 seconds. STEP3 Enter the the 2, 3 or 4-digit code for the channel you want programmed first (for example, 007) using the Number Pad, then press the [STOP] button. Then enter the code for the next channel (for example, 050), then press the [STOP] button. STEP4 Press the [CH ] button to store the channels that were selected. Press again and it will bring up the third channel. 6 Quick Set-up Code Tables TV Quick Number Manufacturer/Brand 0 1 2 3 4 5 6 7 8 9 FUJITSU SONY SAMSUNG LG TOSHIBA PANASONIC PHILIPS HITACHI SHARP PHILIPS 7 Set-up Code Tables CBL-CABLE Converters Manufacturer/Brand CISCO / SA PIONEER PACE SAMSUNG MOTOROLA DIGEO GENERAL INSTRUMENT HAMLIN HITACHI JERROLD MAGNAVOX MEMOREX MOXI NFUSION PANASONIC PHILIPS PULSAR RCA REGAL REGENCY SKY SONY SPRUCER TELNET TOCOM TOSHIBA VIEWSTAR ZENITH TV Manufacturer/Brand BRADFORD BROCKWOOD BROKSONIC BYDESIGN CANDLE CAPEHART CARY AUDIO DESIGN CELEBRITY CENTURION CETRONIC CHANGHONG CITIZEN CLARION CLASSIC CLP CLASSIC COLORTYME CONCERTO CONCIERGE CONTEC CORNEA CORONADO CRAIG CROSLEY CROWN CURTIS MATHES CXC CYBERHOME DAEWOO Set-Up Code Number Set-Up Code Number 001 003 041 042 045 046 001 103 034 051 063 076 105 001 005 002 001 030 002 111 148 153 005 103 104 049 050 055 103 055 005 004 103 005 003 008 009 010 069 010 012 052 111 252 153 192 044 047 006 012 013 020 085 052 047 049 050 057 230 204 108 047 354 039 040 056 052 012 015 052 060 093 100 AUDIO Quick Number Manufacturer/Brand 0 1 2 3 4 5 6 7 8 9 ROTEL DENON YAMAHA MARANTZ SONY INTEGRA HARMAN KARDON PIONEER ONKYO LEXICON DVD Quick Number Manufacturer/Brand 0 1 2 3 4 5 6 7 8 9 HITACHI SONY PHILIPS SAMSUNG PHILIPS MAGNAVOX PANASONIC LG JVC DENON PIONEER TV Manufacturer/Brand A MARK ABEX ACCURIAN ADMIRAL ADVENT ADVENTURA AIKO AKAI Set-Up Code Number J. Programming the System On/Off Button This allows you to program the System On/Off button so it can send up to five power On/Off commands with one button press. STEP2 Press the [SYSTEM ON/OFF] button and the [OK/SEL] button simultaneously for 3 seconds. STEP3 Press the first [COMPONENT] button you want to store in the [SYSTEM ON/OFF] button and then the [POWER] button. Repeat this for other Components until you have stored all the desired power commands into the [SYSTEM ON/OFF] button. The [CBL] button will blink twice to confirm the commands have been saved. 3 Operations DEFAULT STATE: Component Default: CABLE Set Top Box (STB) Channel Default: CABLE channel and numbers through the CABLE STB. [. . . ] You have the option of controlling your CABLE channel and numbers through the TV or AUD. Volume Default: Volume and Mute control are automatically transferred to the respective Component mode you select, as follows: CBL: Cable Set Top Box / TV: TV / AUD:AUD. Volume and Mute control for DVD are automatically transferred to the TV. However, you have the option of controlling CABLE Volume and Mute through the TV, DVD or AUD. [. . . ]