User manual UNIVERSAL REMOTE CONTROL 5IN1

[. . . ] This Owner's Manual is designed to assist you in programming your AVEX R6 remote to work with your components by guiding you through an easy step-by-step process. Everything you need to know about programming the AVEX R6 is contained in this Manual. AVEX R6 Owner's Manual © 2009 Universal Remote Control, Inc. This document is protected by the copyright laws of the United States and internationally by the Berne Convention. [. . . ] The component LED lights will blink three times to confirm that the programming has been successfully saved. CHANNEL UP SUGGESTION: Most of the components have the same signal to turn the power On and Off. You may want to program MacroPower only in the POWER button and save the System Off button to turn components On or Off individually. Note: If you want to program MacroPower for the SYSTEM OFF button, repeat the same steps used for Power ON programming. Page 15 Notes regarding programming multicommands to Macro buttons: · You can program up to 20 commands on each Macro button. · You can program delays in between commands by pressing the PAUSE button. · Also, if you add the delay time as the first step of Macro commands, the remote will not send the Macro unless the button is held for two seconds. · You can also program macro commands in `layers' by pressing the STOP button in between commands. (For example, if you press CBL, 009, STOP, 035, STOP, 365, STOP and the CH+ button in Step 2) the remote will send out 009 at the first press of the `A' button, and then send out 035 at the second press, etc. · You cannot program the CH+ or PAUSE buttons as macro commands. PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE PLEASE CONTACT OUR TECHNICAL SUPPORT CENTER. IF YOU NEED ASSISTANCE, E-MAIL techsupport@UniversalRemote. com or dial 1-800-901-0800 (9:00AM-6:00PM EST) Page 16 Programming "My Favorites" - Favorite Channel Buttons In Cable mode, the A, B, C, D buttons are also designed to serve as dedicated Favorite Channel buttons. Each button will access one of your favorite channels with just one button press. Here's how to program Favorite Channels: STEP 1: Press the CBL button to select the Cable mode. This sets up three buttons (Volume Up, Volume Down and MUTE) as a group for that component. VOLUME UP Repeat Steps 1-2 for all other components. Note: SimpleSound is what's technically referred to as a "Punch Through" feature and is not limited to volume control. If you find yourself switching to a particular component mode frequently to access a particular control, consider using "Punch Through". Page 20 Channel Control "Punch Through" This "Punch Through" enables you to program the AVEX R6 so that either the Cable or TV Channel Controls (CHANNEL UP, DOWN, LAST, CHANNEL NUMBERS 0-9, +10 and ENTER) will also operate in other component modes on the remote control. STEP 1: Press and hold the component button you want to add channel control to, such as DVD or VCR, and the SELECT [SEL] button at the same time for two seconds until the Component LED light turns on. IMPORTANT: You have 30 seconds to perform the next step while you are in programming mode. If you do not press a button within 30 seconds, the component LED light will turn off. The remote will exit the programming mode and you will have to start over. The component LED light will blink once. COMPONENT BUTTONS SELECT CHANNEL UP STEP 3: Press either the TV or CBL button that you want to use as the source of channel control. The component LED will blink three times to confirm it is saved. Page 21 Transport Control "Punch Through" This "Punch Through" enables you to program the AVEX R6 so that VCR or DVD Transport Controls (PLAY, STOP, FF, REW, PAUSE, SKIP and RECORD) will also operate in other component modes on the remote control. STEP 1: Press and hold the component button you want to add Transport Control to, such as CBL or TV, and the SELECT [SEL] button at the same time for two seconds until the Component LED light turns on. IMPORTANT: You have 30 seconds to perform the next step while you are in programming mode. [. . . ] Then once again it will pause, then blink, to indicate the number of the third digit. Example: One blink, pause, eight blinks, pause, three blinks indicates code number 183. Note that ten (10) blinks represent the number 0. Page 30 Pre-Programmed Code Tables The AVEX R6 Pre-Programmed code library is classified by category (TV, VCR, DVD, etc. ). Within each category, the code numbers are listed in rows by brand (Sony, Panasonic, B & K, etc. ). [. . . ]