User manual UNIVERSAL REMOTE CONTROL ATLAS 4-DEVICE

[. . . ] Use SETTINGS/MENU to access additional cable features (see your cable converter's manual). or Use PAGE+ (or PAGE-) to page up (or page down) through menu screens and the program guide. Use the Cursor keys to move the cursor in the program guide and menu screens and to navigate within the interactive service. Use SELECT to choose options, PPV events, and to tune programs from the program guide. continued on the next page. . . 5 Atlas Manual rev2 12/27/02 11:07 AM Page 6 FEATURES AND FUNCTIONS Key Charts (continued) After programming, press MACRO once to run a macro (see Using Macros on page 26). Use A, B, or C to access additional cable features (see your cable converter's manual). Use DAY+ (or DAY-) to move a day forward (or back) on your cable converter's program guide. [. . . ] The TV key will blink twice. 2. 3. To view the code for the first digit, press 1 once. Wait 3 seconds and count the number of times the TV key blinks (e. g. , 3 blinks = 3) and write down the number in the leftmost TV Code box (see below). NOTE: If a code digit is "0", the selected mode key will not blink. 4. Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. To check for other device codes, repeat steps 1 through 4, but substitute the appropriate key (i. e. , AUD, VCR, or CABLE) for the (Audio, VCR, or Cable) device you are checking. Write down the codes in the appropriate boxes below. AUD Code Audio Device ____________________ VCR Code 5. TV Code CABLE Code 21 Atlas Manual rev2 12/27/02 11:07 AM Page 22 PROGRAMMING ID LOCK The Atlas Universal Remote Control is preprogrammed and locked at the factory to operate a Scientific Atlanta cable converter. However, if you have another brand or model of cable converter and interactive service that you would like to control, then you'll need to perform the following steps to unlock the cable ID Lock, enter in a new manufacturer's code, and lock the ID Lock again. Then press and hold SETUP until the CBL key blinks twice, then release SETUP. Perform the instructions in Programming Device Control on page 8 to program device control for the desired cable converter and interactive service. Upon completion, perform the remaining steps (5 and 6 on this page) to again lock the ID lock. Then press and hold SETUP until the CBL key blinks twice, then release SETUP. The CBL key will blink twice. 3. 4. 5. 6. 22 Atlas Manual rev2 12/27/02 11:07 AM Page 23 PROGRAMMING CHANNEL CONTROL LOCK By default, the remote control's channel-control capabilities are locked to the cable converter. This will guarantee that you do not inadvertently change a channel on your TV or VCR. However, you can de-activate this feature to allow full access to these keys in the TV and VCR modes. *NOTE: This feature does not affect the AUD mode. To De-Activate Channel Control Lock: 1. Then press and hold SETUP until the CBL key blinks twice, then release SETUP. Now, the remote control will provide TV and VCR channel-control capabilities while in the TV or VCR mode. To Re-Activate Channel Control Lock: 1. Then press and hold SETUP until the CBL key blinks twice, then release SETUP. Now, regardless of what mode you select (i. e. , TV, VCR, or CBL), only the channel control capability of your cable converter will be accessible. 23 Atlas Manual rev2 12/27/02 11:07 AM Page 24 USING THE MASTER POWER KEY The Atlas Universal Remote Control has a unique feature that allows you to sequentially turn on or off all of your home entertainment devices with a single key press. NOTE: MASTER POWER only works in the CBL mode. If it is not programmed, only the cable converter will turn on or off. In any other mode, pressing MASTER POWER once will turn on or off the selected device. To Program The Master Power Key: 1. On the remote control, press and hold SETUP until the last-selected device key blinks twice, then release SETUP. Then press POWER once. 2. 3. For the first device you want in the power on sequence, press a device key (e. g. , CBL) once and then press POWER once. Repeat step 3 up to three more times to add the second, third, and fourth device, as desired. [. . . ] PROBLEM: CH+ , CH ­ , and LAST do not work for your RCA TV. SOLUTION: Due to RCA design (1983-1987), only the original remote control will operate these functions. SOLUTION: If original remote control required pressing ENTER to change channels, press ENTER on the remote control after entering a channel number. PROBLEM: Tried "Search Method" and still could not find a working code. SOLUTION: Try the "Search Method" again after clearing out the device key as follows: Press and hold SETUP until mode key blinks twice, then release. PROBLEM: Remote control does not turn on Sony or Sharp TV/VCR Combo. SOLUTION: For power on, these products require programming TV codes on the remote control. [. . . ]