User manual UNIVERSAL REMOTE CONTROL ATLAS OCAP 5-DEVICE

[. . . ] Atlas OCAP M1056L. fm Page 1 Friday, December 22, 2006 6:10 PM ATLAS OCAP 5-Device Remote Control with Learning Users Guide PREPROGRAMMED FOR YOUR SET-TOP BOX Atlas OCAP M1056L. fm Page 2 Friday, December 22, 2006 6:10 PM TABLE OF CONTENTS Introduction . 18 Unlocking Volume Control for a Single Device (Individual Volume Unlock) . 19 Locking Volume Control To One Mode (Global Volume Lock) 19 Programming Cable ID Lock. 43 www. urcsupport. com/atlasocap 2 Atlas OCAP M1056L. fm Page 3 Friday, December 22, 2006 6:10 PM Setup Codes for DVR/PVR Systems . [. . . ] The Atlas OCAP 5-Device Remote Control with Learning's LED will blink rapidly, then turn off. Continue holding www. urcsupport. com/atlasocap 15 Atlas OCAP M1056L. fm Page 16 Friday, December 22, 2006 6:10 PM NOTE: 6. the key on the original remote until the Atlas OCAP 5-Device Remote Control with Learning's LED blinks twice. If the function is still not captured, press and hold SETUP to exit programming and review the "Learning Precautions" on the previous page. Repeat steps 2 through 5 for another mode and/or key or press and hold SETUP to exit programming. Deleting a Single Learning Key This process returns the key to its original programming for the mode you select. You can also delete learned programming by teaching a different function to the key (see "Programming a Learned Key" on page 15) NOTE: If more than 15 seconds pass between key presses, the remote exits programming. Press and hold SETUP until the last-selected mode key blinks twice, then press 9 7 6. 2. Press a mode key once (i. e. , VCR, DVD, AUD, TV, or CBL). Repeat steps 2 through 3 for another key or press and hold SETUP to exit programming. 3. 4. www. urcsupport. com/atlasocap 16 Atlas OCAP M1056L. fm Page 17 Friday, December 22, 2006 6:10 PM Deleting All Learned Keys in a Specific Mode NOTE: If more than 15 seconds pass between key presses, the remote exits programming. Press and hold SETUP until the last-selected mode key blinks twice, then press 9 7 5. 2. 3. Press a mode key twice (i. e. , VCR, DVD, AUD, TV, or CBL) to clear all the learned keys for that mode. Repeat step 2 for another mode or press and hold SETUP to exit programming. PROGRAMMING CHANNEL CONTROL LOCK By default, the remote control's channel-control capabilities are locked to the cable converter. This will guarantee that you do not inadvertently change a channel on your TV or VCR. However, you can deactivate this feature to allow full access to these keys in the TV and VCR modes. The CBL key will blink four times. Now the remote control will provide TV and VCR channel-control capabilities while in the TV or VCR mode. www. urcsupport. com/atlasocap 17 Atlas OCAP M1056L. fm Page 18 Friday, December 22, 2006 6:10 PM Locking Channel Control to CBL 1. The CBL key will blink twice. Now, regardless of what mode you select (except AUD), the channel keys will only change channels on your cable converter. CHANGING VOLUME LOCK Volume Lock allows you to control the volume through the device identified as having your primary speaker(s), regardless of which mode you are using. On the Atlas OCAP 5-Device Remote Control with Learning, Global Volume Lock is set to TV, so you can control TV volume while in the VCR, DVD, TV or CBL mode. You can perform Individual Volume Unlock on a selected device to set its volume control for independent operation. NOTE: The audio mode's (AUD) volume controls are active regardless of Volume Lock settings. However, if you lock the volume controls to the AUD mode, you will have control of the audio device's volume in all other modes (i. e. , VCR, DVD, TV, and CBL). This can be an advantage if, for example, you always listen to home entertainment devices through your receiver's speakers. Unlocking Volume Control for a Single Device (Individual Volume Unlock) 1. Assuming Global Volume Lock is active, select a mode on the remote control that you want to unlock (e. g. , CBL) and press it once. [. . . ] PROBLEM: Device key blinks when you press a key, but home entertainment device does not respond. SOLUTION: Make sure you are aiming the remote control at your home entertainment device and that you are within 15 feet of the device you are trying to control. PROBLEM: The remote control does not control home entertainment devices or commands are not performing properly. Make sure all devices can be operated with an infrared remote control. [. . . ]