User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL 4605 WO CODE

[. . . ] If the batteries are inserted correctly, the LED will blink once. NOTE: When batteries need replacement, the remote control will stop operating. Remove the old batteries and insert new ones within 30 minutes to ensure all of your programming information is restored. PROGRAMMING TV/VCR COMBO CONTROL Perform the following instructions to control a TV/VCR Combo: 1. Turn on the TV/VCR Combo and insert a video cassette. NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. CHECKING THE CODES If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment: For example, to find out which code is operating your TV: 1. [. . . ] Use the Setup Codes For TV/VCR Combos (on the back side) to locate the brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again. PREV SHIFT MENU CH VOL ­ MUTE VOL + When a re-assignment is done, the LED will blink twice to confirm your choice. At that time, you will need to program the remote control for the new device (see Programming Device Control). SOLUTION: Try all listed codes for the component brands being set up. PROBLEM: TV/VCR combo does not respond properly. CH SLEEP SKIP REV REW PLAY REC PAUSE STOP FF ENTER TV/VID PROGRAMMING DEVICE CONTROL The One For All Access 4 remote control is preprogrammed at the factory to operate an RCA TV and VCR, a Motorola (GI) cable box, and a Toshiba DVD player. To control devices other than the default brands, perform the following steps; otherwise skip this section: NOTE: For TV/VCR Combo control, see the next section. EXIT MENU 4. If the device does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (Play) key. 5. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. To check for codes of other devices, repeat steps 1 through 5, but substitute the appropriate device key for each device you are checking. As before, write down each fourdigit code. CHANGING VOLUME LOCK The One For All Access 4 is set to control the volume of your TV in the TV, VCR, CBL/SAT, and DVD modes. If you want the volume to be controlled by a mode other than TV (e. g. , CBL/SAT), change the Volume Lock as follows: SOLUTION: Use the VCR codes for your brand. Some combo units may require both a TV code and a VCR code for full operation. PROBLEM: Changing channels does not work properly. USER'S GUIDE VOL ­ VOL + Use VOL+ (or VOL-) to raise (or lower) the sound volume. Use CH+ (or CH -) to select the next higher (or lower) channel. To Change Volume Lock To Another Mode: 1. On the remote control, press and hold SET until the LED blinks twice, then release SET. Now, whenever you press VOL+, VOL­, or MUTE, volume will be controlled by your mode choice. SKIP FWD CH INTRODUCTION The One For All Access 4 Universal Remote Control is designed to operate three (or four) home entertainment devices, depending on the model purchased (see Key Charts, Mode Keys on the right). The remote control requires two fresh AAA alkaline batteries and easy programming to control your devices. For best results, please read and perform all instructions listed here. Also, keep these instructions for future reference. CH 1. Turn on a device (e. g. , VCR) and, if applicable, insert media, (e. g. , cassette or disc). NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. Aim the remote control at the the TV and slowly alternate between pressing POWER and TV. [. . . ] One For All® Access 4 is compatibile for use in North America excluding Mexico. On the remote control, press and hold SET until the LED blinks twice, then release SET. Volume will again be controlled according to its default states. SOLUTION: Due to RCA design (19831987), only the original remote control will operate these functions. PROBLEM: Remote control does not turn on Sony or Sharp TV/VCR Combo. FEATURES AND FUNCTIONS Use the Key Charts to learn how to use the universal functions of the One For All Access 4 Universal Remote Control. SLEEP Key Charts REW Press SLEEP to activate your device's sleep timer (not available for all devices). PLAY FF SET Use SET for all programming sequences. [. . . ]