User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL 8011

[. . . ] Use VOL+ (or VOL-) to raise (or lower) the sound volume. SETTING UP YOUR COMPONENTS The One For All 8 Device Home Theater Universal Remote Control is preprogrammed at the factory to operate an RCA TV and VCR, a Motorola (GI) cable box, an RCA satellite receiver, a Pioneer CD player, a Toshiba DVD player, a Pioneer audio receiver/ amplifier, and a One For All home automation device. To control devices other than the default brands, perform the following steps; otherwise skip this section: NOTE: For TV/VCR Combo control, see the next section. TV/VCR Code: TV Code (if used): 4. 8 DEVICE HOME THEATER UNIVERSAL REMOTE CONTROL Press MUTE once to turn the sound off or on. In TV, VCR, DVD, SAT, and CBL modes, use FAV to scan favorite channels and/or all channels. (See Using Channel Scan and Programming Favorite Channel Scan. ) ND Select a device. [. . . ] (See Setting Up Your Components. ) To re-assign other device keys to the AUX key, repeat steps 1 through 4 above by substituting the sequence from the below chart: · Home entertainment or home automation devices not controlled by remote controls. · Infrared keyboards and infrared pointing devices (such as mouse substitutes). · All products for sale and/or use outside the continental United States, Hawaii, Alaska, or Canada. PROGRAMMING FAVORITE CHANNEL SCAN In the TV, VCR, DVD, SAT, or CBL mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when FAV is pressed (see Using Channel Scan). NOTE: Only channels of one mode can be stored for Favorite Channel Scan. To Re-Assign Device Key AUX as 2nd TV key: AUX as 2nd DVD key: AUX as 2nd SAT key: AUX as 2nd CD key: AUX as 2nd CBL key: AUX as 2nd RCVR/AMP key: Perform Sequence SET - 9 - 9 - 2 - TV - AUX SET - 9 - 9 - 2 -DVD- AUX SET - 9 - 9 - 2 -SAT- AUX SET - 9 - 9 - 2 -CD- AUX SET - 9 - 9 - 2 -CBL- AUX SET - 9 - 9 - 2 - RCVR/AMP - AUX USER'S GUIDE INTRODUCTION The One For All 8 Device Home Theater Universal Remote Control is designed to operate up to eight home entertainment devices, including TV, video, and audio components. The remote control requires two (2) new AA alkaline batteries (not included) and easy programming to control your devices. For best results, please read and perform all instructions listed here. Also, keep these instructions for future reference. To record a VCR program, press REC twice. 4. To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e. g. , three blinks = 3) and write down the number. NOTE: If a code digit is "0", the LED will not blink. USING A MACRO With programming, the MACRO key on your One For All 8 Device Home Theater Universal Remote Control can be setup to perform a repetitive, time-consuming operation for easy, convenient access through the press of a single key. A macro can be used to control a home theater operation, to set a favorite channel, or for other multiple functions you would like to control with one key press (see examples below). LED blinks when you press a key, but home entertainment device does not respond. SOLUTION: Replace batteries with two new AA alkaline batteries. USING THE HOME THEATER MODE The One For All 8 Device Home Theater Universal Remote Control includes a custom Home Theater mode. After the HOME THEATER key is programmed, it will allow you to access five groups of remote control keys without having to change device modes. SOLUTION: Make sure the remote control is aimed at your home entertainment device and is not farther than 15 feet away. PROBLEM: The unit does not control home entertainment devices or commands are not working properly. FEATURES AND FUNCTIONS Use the Key Charts (below) to learn how to use the universal features and functions of the One For All 8 Device Home Theater Universal Remote Control. Example ­ Programming A Favorite Channel With so many channels available through your cable or satellite system provider, you can program a macro that directly selects a favorite channel with one key press. For example, let's assume your favorite cable programs are on channel 71. Use the following instructions to program a macro for direct access of this channel: NOTE: This example assumes the TV tuner is connected directly to the cable line and not through a cable box. CHANGING VOLUME LOCK The One For All 8 Device Home Theater Universal Remote Control is set at the factory for independent volume control of each selected device. However, you may change the Volume Lock setting to Global Volume Lock so that a device's volume will be locked to one mode (e. g. , to control TV volume in all other modes). After that, if desired, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation. Control Organization About Control Groups 5. If desired, repeat step 4 (in this section) for each favorite channel to be stored, up to a total of 10 channels. NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming. Key Charts The LED (red light) blinks to show that the remote control is working and is sending signals. Press TV, VCR, DVD, AUX, SAT, CBL, RCVR/AMP, or CD once to select a desired home entertainment device to control. After programming, press HOME THEATER once to select the home theater mode (see Using The Home Theater Mode). Press MENU once to display your selected device's main menu. SOLUTION: Try all listed codes for the device brands being set up. Some combo units may require both a TV code and a VCR code for full operation. SOLUTION: If original remote control required pressing ENTER to change channels, press ENTER on the remote control after entering the channel number. PROBLEM: Tried Search For Your Code method and still could not find a working code. For Home Theater programming, the remote control's keys are grouped by type of control into the following five control groups: 6. SETTING UP TV/VCR COMBO CONTROL Perform the following instructions to control a TV/VCR Combo: 1. Turn on the TV/VCR Combo and insert a video cassette. NOTE: Please read steps 2 through 4 completely before proceeding. [. . . ] Upon completion of the above procedure, you can now use your One For All 8 Device Home Theater Universal Remote Control to control the TV's volume and mute in the VCR mode, as well as in the TV mode. Now, after you select a device that has volume unlocked (e. g. , RCVR/AMP), pressing VOL+, VOL­, or MUTE, will control the device's volume only in its own mode. b. Test the remote control by first pressing POWER and then any mode key (e. g. , TV). If batteries are inserted correctly, the LED (red light) will blink once. NOTE: When batteries need replacement, the remote control will stop operating. [. . . ]