User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL 8811 WO CODE

[. . . ] In TV, VCR, DVD, SAT, and CBL modes, use FAV to scan favorite channels and/or all channels. Press and hold SET until the LED (red light) blinks twice, then release SET. Use the Manufacturer's Codes (on the back) to locate the type of device and brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try entering the same code again. CHECKING THE CODES If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment. [. . . ] Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. To obtain warranty service for a defective product during the warranty period, please return the product, preferably in the original carton, along with your purchase receipt, to the store of original purchase. A note detailing the complaint would be helpful. The store, at its option, will replace or repair this product if found to be defective. Press and hold SET until the LED (red light) blinks twice, then release SET. Use the Setup Codes For TV/VCR Combos (on the back) to locate the brand name and then enter the first four-digit code for your device. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, repeat steps 2 through 4 and try entering the same code again. ABOUT UPGRADING The One For All 8L Home Theater Upgradeable Universal Remote Control with Learning has the largest infrared code library available. However, if you purchase a brand new home entertainment or home automation device, it may not respond to the codes stored in the remote control's memory. If this happens, please contact our Customer Support department (see Customer Support below) to upgrade the remote control. The Customer Support representative will search our entire database for a code that matches your device and instruct you how to enter it into your One For All 8L Home Theater Upgradeable Universal Remote Control with Learning. If the code for your home entertainment or home automation device is not in our database, we will need to "capture" the code for that device from its original remote control. A new code would then be created and entered into your One For All 8L Home Theater Upgradeable Universal Remote Control with Learning. If necessary, the Customer Support representative can instruct you how to begin the capture procedure. NOTE: One For All reserves the right to replace a returned remote control with a new one of equal or superior functionality. The default Device Group setting from the factory is: 5. Then enter the following sequence: CBL, POWER, and 1-1 (or 0 -1- 1 if access is over 100 channels) 6. Now when you press M2 once, the TV will turn on and tune to channel 03. Then the cable box will turn on and tune to channel 11. To Re-Assign Device Key AUX as 2nd TV key: AUX as 2nd DVD key: AUX as 2nd SAT key: AUX as 2nd CD key: AUX as 2nd CBL key: AUX as 2nd RCVR/AMP key: Perform Sequence SET - 9 - 9 - 2 - TV - AUX SET - 9 - 9 - 2 -DVD- AUX SET - 9 - 9 - 2 -SAT- AUX SET - 9 - 9 - 2 -CD- AUX SET - 9 - 9 - 2 -CBL- AUX SET - 9 - 9 - 2 - RCVR/AMP - AUX Clearing A Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Press and hold SET until the LED blinks twice, then release SET. FEATURES AND FUNCTIONS Use the Key Charts (below) to learn how to use the universal features and functions of the One For All 8L Home Theater Upgradeable Universal Remote Control with Learning (URC-8811). 5. If the device does not respond, repeat steps 2 through 5, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (Play) key. Programming The Home Theater Mode For example, let's assume you have a TV, a cable box, and a VCR in your home theater system. You can set up the Home Theater mode so that selected controls are assigned to these devices as follows: 1. Press and hold SET until the LED (red light) blinks twice, then release SET. For this example, press PLAY once, which will assign the entire group of Transport Controls (i. e. , PLAY, STOP, FWD, REW, PAUSE, and REC) to the VCR. [. . . ] Copyright 2002 by Universal Electronics Inc. No part of this publication may be reproduced, transmitted, transcribed, stored in any retrieval system, or translated to any language, in any form or by any means, electronic, mechanical, magnetic, optical, manual, or otherwise, without the prior written permission of Universal Electronics Inc. The One For All® 6 Device Universal Remote Control is compatibile for use in North America, excluding Mexico. URC-8810w/8811 02/02 SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. Press and hold SET until the LED (red light) blinks twice, then release SET. [. . . ]