User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL IMPK6VR

[. . . ] IMPK6VR manual 1. 0 2/21/03 5:46 PM Page 1 6-DEVICE PVR Universal Remote Control User's Guide IMPK6VR manual 1. 0 2/21/03 5:46 PM Page 2 TABLE OF CONTENTS Introduction . 16 Unlocking Volume Control For A Single Device (Individual Volume Unlock) . 36 2 IMPK6VR manual 1. 0 2/21/03 5:46 PM Page 3 INTRODUCTION The One For All 6-Device PVR Universal Remote Control (URC-6131) is designed to remotely operate up to six home entertainment devices and features intuitive and easy-to use buttons to operate PVR (Personal Video Recorders) and DVD components. Its sophisticated technology will allow you to consolidate all of your original home entertainment remote controls into one easy-to-use product. Advanced features include: · Intuitive buttons to allow easy access to your PVR or DVR (Digital Video Recorder) functions and menus · Direct code setup for easy device programming · Step and Set code setup and Code Verification for an alternate way to program devices · Master Power function for master on/off control of all of your equipment with a single keystroke · Volume Lock to lock volume controls to one mode or individual modes · Device Key Re-Assignment to remotely control a second (duplicate) device · Color-coded keys to quickly locate popular functions · Code library for popular video and audio devices The URC-6131 remote control requires two (2) new AA alkaline batteries (not included) and some easy programming to control your devices. [. . . ] The LED will blink twice. 4. To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e. g. , three blinks = 3) and write down the number in the leftmost box in the TV code boxes on page 10 NOTE: If a code digit is "0", the LED will not blink. 5. Repeat step 4 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit. To check for codes of other devices, repeat steps 1 through 5, but substitute the appropriate device key for each device you are checking. Write down the device's code digits in the appropriate code boxes on page 10. 6. PROGRAMMING MASTER POWER In its default state, the POWER key on the URC-6131 remote control will individually power your home entertainment devices on or off. However, you can also program a Master Power function onto the POWER key that will sequentially turn on or off all the devices with a single key press. Programming The Power Key For Master Power 1. Press and hold SET until the LED (red light) blinks twice, then release SET. 12 IMPK6VR manual 1. 0 2/21/03 5:46 PM Page 13 2. Enter 9 - 9 - 5. Then press POWER once. 3. For the first device you want in the power on sequence, press its device key (e. g. , CBL/SAT) once. Repeat step 3 up to five more times to add desired devices to the power-on sequence. To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on or off your devices. NOTE: When POWER is pressed for less than 2 seconds, a power command will only be sent to the currently-selected device. 5. Operating Master Power 1. 2. You will see the devices turn on or off according to your programmed sequence. NOTE: The currently-selected device will always turn on first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s). Press and hold SET until the LED (red light) blinks twice, then release SET. Then press POWER once. 3. Press and hold SET until the LED blinks twice, then release SET. Master Power is now cleared. 13 IMPK6VR manual 1. 0 2/21/03 5:46 PM Page 14 USING KEYMOVER The One For All 6-Device PVR Universal Remote Control includes a Keymover feature that allows you to map (or copy) keys from one mode (i. e. , source mode) to another mode (i. e. , destination mode). NOTE: The following keys cannot be used as a source or destination: TV, PVR, DVD, CBL/SAT, AUD, VCR, and SET. Programming Keymover For example, if your VCR does not have volume control, you can map those keys (i. e. , VOL+, VOL-, and Mute) from the TV mode to the VCR mode as follows: 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Repeat steps 1 through 7 twice more to map remaining volume control keys, substituting VOL- and Mute as source and destination keys in steps 4 and 6. Upon completion of the above procedure, you can now use your One For All 6-Device PVR Universal Remote Control to control the TV's volume and mute in the VCR mode, as well as in the TV mode. Restoring Keymoved Keys to Default Settings Restoring A Single Keymoved Key 1. Press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. 4. Press the destination key twice (where the keymoved key is stored). 14 IMPK6VR manual 1. 0 2/21/03 5:46 PM Page 15 Restoring All Keymoved Keys In A Single Mode 1. Press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. RE-ASSIGNING DEVICE KEYS The One For All 6-Device PVR Universal Remote Control can be set to control a second TV, PVR, VCR, DVD player, or other device. [. . . ] The Customer Support representative will search our entire database for a code that matches your device and instruct you how to enter it into your One For All 6-Device PVR Universal Remote Control. If the code for your home entertainment or home automation device is not in our database, we will need to "capture" the code for that device from its original remote control. A new code would then be created and need to be entered into your One For All 6-Device PVR Universal Remote Control. If necessary, the Customer Support representative can instruct you how to begin the capture procedure. NOTE: One For All reserves the right to replace a returned remote control with a new one of equal or superior functionality. Upgrade Exclusions · Home entertainment devices controlled by radio frequency (RF/UHF), wired, or ultrasonic remote controls. [. . . ]