User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL URC3110

[. . . ] On the remote control's back, push the tab and lift off the battery cover. 4. NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again. Aim the remote control at the device and press POWER once. If it does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (PLAY) key. 5. [. . . ] If your TV/DVD does not respond, repeat steps 2-4, trying each code listed for your brand until you find the one that operates your TV/DVD. 1. Turn on a device (e. g. , VCR) and, if applicable, insert media, (e. g. , cassette or disc). NOTE: Please read steps 2-4 completely before proceeding. Highlight or write down the codes and device you wish to program before moving on to step 2. 2. On the remote control, press a device key once (i. e. , VCR/DVD, CBL/SAT, or TV). Press and hold SET until the LED blinks twice, then release SET. 3. Use the Manufacturer's Codes (starting on page 11) to locate the type of device and brand name and then enter the first four-digit code for your component. Your One For All 3 Devices is now programmed to operate your TV/DVD. Write your TV/DVD code for future reference. Remember, if you want to use your One For All 3 Devices to operate your TV/DVD, press the VCR/DVD key first. 5 6 CTGRD3N 3110 manual booklet. QXD 5/2/06 3:08 PM Page 7 SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. Press and hold SET until the LED blinks twice, then release SET. 2. To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the below chart for the most popular components: 3. Aim the remote control at the the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off. To Re-Assign Key VCR/DVD as 2nd TV key: VCR/DVD as 2nd CBL key: VCR/DVD as 2nd SAT key: VCR/DVD back to VCR/DVD: Sequence Perform SET - 9 - 9 - 2 - TV - VCR/DVD SET - 9 - 9 - 2 - CBL/SAT - VCR/DVD SET - 9 - 9 - 2 - CBL/SAT - VCR/DVD SET - 9 - 9 - 2 - VCR/DVD - VCR/DVD NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first. 5. To lock in the code, press and hold SET until the LED blinks twice, then release SET. When a re-assignment is done, the LED will blink twice to confirm your choice. At that time, you will need to program the remote control for the new device (see Setting Up Your Components). 6. To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate device key for the device you are searching for. CHANGING VOLUME LOCK The One For All 3 Devices is set to control the volume of your TV in the TV, VCR, CBL/SAT, and DVD modes. If you want the volume to be controlled by a mode other than TV (e. g. , CBL/SAT), change the Volume Lock as follows: CHECKING THE CODES If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment: For example, to find out which code is operating your TV: 1. Press and hold SET until the LED blinks twice, then release SET. To Change Volume Lock To Another Mode: 1. On the remote control, press and hold SET until the LED blinks twice, then release SET. Now, whenever you press VOL+, or VOL­, volume will be controlled by your mode choice. Enter 9 - 9 - 0. Tried "Search Method" and still could not find a working code. Clear the device key as follows: Press and hold SET until the LED blinks twice, then release. Now repeat the "Search Method. " CH + and CH - do not work for your RCA TV. INSTRUCTIONS TO THE USER This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interference in a residential installation. [. . . ] Suite 1000 Louisville, KY 40299 USA together with the original receipt and $3. 95 to cover postage and handling. The manufacturer reserves the right to substitute a currently manufactured model with equal or superior features. PROBLEM: SOLUTION: PROBLEM: SOLUTION: PROBLEM: SOLUTION: Due to RCA design (1983- 1987), only the original remote control will operate these functions. If the above does not work. Please contact us in any of the following ways: PROBLEM: SOLUTION: · Please visit : www. oneforall. com · If the above website is not able to provide you with the information you need, please email us at ofasupport@ueic. com · Customer Support : (330) 405-8612 9 10 CTGRD3N 3110 manual booklet. QXD 5/2/06 3:08 PM Page 11 ADDITIONAL INFORMATION As you update your home entertainment system, One For All® has a universal remote control that will fit your needs. Look for these exciting products at a retailer near you. One For All Access 3 . [. . . ]