User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL URC3220

[. . . ] For master power control, see Programming A Master Power Macro on page 10. Use the keypad (1 ~ 9 and 0) to directly select channels (e. g. , 009 or 031). Use REW, PLAY, FWD, PAUSE, or STOP to control your VCR, PVR (or DVR), or DVD player. For a VCR, PVR (or DVR), or VOD (if available), use SCANor SCAN+ to quickly scan forward or back through a video program. Use QUICK SKIP to advance the video program a preset amount (as set on your device). [. . . ] To save the settings and exit the program, press and hold SET until the LED blinks twice, then release SET. CHECKING THE CODES If you have set up the remote control using the Searching For Your Code procedure as above, you may need to find out which four-digit code is operating your equipment. Press and hold SET until the LED (red light) blinks twice, then release SET. After programming, point the remote control at the devices and press POWER for at least 2 seconds to sequentially turn on (or off) your devices. NOTE: When POWER is pressed for less than 2 seconds, a power command will only be sent to the currently-selected device. To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e. g. , three blinks = 3) and write down the number in the leftmost box in the TV code boxes on page 8. NOTE: If a code digit is "0", the LED will not blink. Devices will turn on (or off) according to your programmed sequence. NOTE: The currently-selected device will always turn on or off first, followed by the remaining programmed sequence. After the master power sequence has been completed, the remote control will be set to control the first powered-on device. NOTE: If one or more devices does not have a POWER key, the power off/on sequence may be slightly delayed when the remote control signals the device(s). This action is normal. continued on next page. . . 9 10 WALRB3P manual booklet 5/2/06 3:13 PM Page 11 PROGRAMMING A MASTER POWER MACRO (cont'd) Clearing The Master Power Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Then press POWER once. PROGRAMMING FAVORITE CHANNEL SCAN In the CBL/SAT or TV mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when FAV is pressed (see Using Channel Scan on the previous page). NOTE: Favorite channels can only be programmed for one mode. After programming, if FAV is pressed while in another mode, the remote control will start scanning all channels instead (if applicable to the selected device). 1. On the remote control, press CBL/SAT or TV once. 3. Press and hold SET until the LED blinks twice, then release SET. 3. Press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. RE-ASSIGNING DEVICE KEYS The One For All 3 Device Universal Remote Control can be set to control a DVD player and a VCR (or a PVR) or a second DVD player by re-assigning the unused CBL/SAT key as follows: 1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. 4. Use the keypad to enter a favorite channel number (e. g. , 031). Then press SET once. NOTE: If the original remote control required pressing an Enter key to change the channel, also press the ENTER key after the channel number (e. g. , 0 - 3 - 1 - ENTER). On some satellite receivers and cable boxes, you may need to press the SELECT (OK) key instead of ENTER. 5. Press CBL/SAT once. The LED will blink twice. The CBL/SAT key is now ready to be set up to control your VCR (or PVR) or second DVD player. See Programming Device Control on page 8. If desired, repeat step 4 for each channel to be stored, up to a total of 10 channels. NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming. To change your favorite channel list at this point, you will first need to delete the existing list by performing the steps in "Clearing Custom Programming"on page 14. Then, perform the instructions in this section once again. 6. NOTE: Only one device can be assigned to an unused device key at a time. USING CHANNEL SCAN In the CBL/SAT or TV mode, use the FAV key to start a 3-second scan of all channels. Or, if programmed, use the FAV key to scan only your favorite channels to view a desired channel (see Programming Favorite Channel Scan on next page. Press CBL/SAT or TV once. To exit programming with less than 10 favorite channels stored, press and hold SET until the LED blinks twice. Otherwise, the remote control will automatically exit the program after 10 channels have been stored. CHANGING VOLUME LOCK The One For All 3 Device Universal Remote Control is set at the factory for independent volume control of each selected device. However, you may change the Volume Lock setting to Global Volume Lock so that a device's volume will be locked to one mode (e. g. , to control TV volume in all other modes). After that, if desired, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation. 2. Press FAV once. · If Favorite Channel Scan has been set up, scanning of favorite channels will start with up to 100 channel changes or until stopped by pressing any key. · If Favorite Channel Scan has not been set up, scanning will start with the current channel, and continue up to 100 channel changes or until stopped by pressing any key. Locking Volume Control To One Mode (Global Volume Lock) 1. [. . . ] Tried Searching For Your Code method and still could not find a working code. Clear the device key as follows: Press and hold SET until the LED (red light) blinks twice, then release. Now repeat the Searching For Your Code method on page 9. CH + and CH - do not work for your RCA TV. PROBLEM: SOLUTION: PROBLEM: SOLUTION: PROBLEM: SOLUTION: PROBLEM: SOLUTION: PROBLEM: SOLUTION: Due to RCA design (1983-1987), only the original remote control will operate these functions. See Changing Volume Lock on page 12 to lock/unlock volume. For assistance, please contact us in any of the following ways: · · · E-mail: ofasupport@ueic. com Internet: http://www. oneforall. com Consumer Help Line: (330) 405-8612 One For All: (330) 405-8655 URC-3220 01/06 INSTRUCTIONS TO THE USER This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. [. . . ]