User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL URC4110

[. . . ] To record a program, press the record key (REC) twice. 3 4 CTGRD4N 4110 manual booklet. QXD 5/2/06 3:09 PM Page 5 INSTALLING BATTERIES 1. On the remote control's back, push the tab and lift off the battery cover. 4. Aim the remote control at the device and press POWER once. If it does not respond, repeat steps 2-3, trying each code for your brand until you find one that works. If it still does not work, try Searching For Your Code. NOTE: If the device does not have a POWER key, press the (PLAY) key. 5. [. . . ] If your original TV/DVD remote control did not have a POWER key, press PLAY. Your TV/DVD should start to play. If your TV/DVD does not respond, repeat steps 2-4, trying each code listed for your brand until you find the one that operates your TV/DVD. 2. On the remote control, press a device key once (i. e. , VCR, DVD, TV, or CBL/SAT ). Press and hold SET until the LED blinks twice, then release SET. 5. Your One For All 4 Devices is now programmed to operate your TV/DVD. Write your TV/DVD code for future reference. Remember, if you want to use your One For All 4 Devices to operate your TV/DVD, press the DVD key first. 3. Use the Manufacturer's Codes (starting on page 12) to locate the type of device and brand name and then enter the first four-digit code for your component. If performed correctly, the LED will blink twice. NOTE: If the LED did not blink twice, then repeat steps 2 through 3 and try entering the same code again. 5 6 CTGRD4N 4110 manual booklet. QXD 5/2/06 3:09 PM Page 7 SEARCHING FOR YOUR CODE If your device does not respond to the remote control after trying all codes listed for your brand, or if your brand is not listed at all, try searching for your code. Press and hold SET until the LED blinks twice, then release SET. 4. (See Setting up your components. ) To re-assign other device keys, repeat steps 1 through 4 by substituting the key sequence from the below chart for the most popular components: To Re-Assign Key VCR as 2nd TV key: VCR as 2nd CBL key: VCR as 2nd SAT key: VCR as 2nd DVD key: VCR back to VCR: DVD as 2nd TV key: DVD as 2nd CBL key: DVD as 2nd SAT key: DVD as 2nd VCR key: DVD back to DVD: Sequence Perform SET - 9 - 9 - 2 - TV - VCR SET - 9 - 9 - 2 - CBL/SAT - VCR SET - 9 - 9 - 2 - CBL/SAT - VCR SET - 9 - 9 - 2 - DVD - VCR SET - 9 - 9 - 2 - VCR - VCR SET - 9 - 9 - 2 - TV - DVD SET - 9 - 9 - 2 - CBL/SAT - DVD SET - 9 - 9 - 2 - CBL/SAT - DVD SET - 9 - 9 - 2 - VCR - DVD SET - 9 - 9 - 2 - DVD - DVD Enter 9 - 9 - 1. Aim the remote control at the TV and slowly alternate between pressing POWER and TV. Stop when the TV turns off. NOTE: In the search mode, the remote control will send IR codes from its library to the selected device, starting with the most popular code first. 5. To lock in the code, press and hold SET until the LED blinks twice, then release SET. 6. To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate device key for the device you are searching for. CHECKING THE CODES If you have set up the remote control using the Searching For Your Code procedure, you may need to find out which four-digit code is operating your equipment: For example, to find out which code is operating your TV: 1. Press and hold SET until the LED blinks twice, then release SET. When a re-assignment is done, the LED will blink twice to confirm your choice. At that time, you will need to program the remote control for the new device (see Setting up your components). CHANGING VOLUME LOCK The One For All 4 Devices is set to control the volume of your TV in the TV, VCR, CBL/SAT, and DVD modes. If you want the volume to be controlled by a mode other than TV (e. g. , CBL/SAT), change the Volume Lock as follows: To Change Volume Lock To Another Mode: 1. On the remote control, press and hold SET until the LED blinks twice, then release SET. Now, whenever you press VOL+, VOL­, or MUTE, volume will be controlled by your mode choice. Enter 9 - 9 - 0. LED blinks when you press a key, but home entertainment component does not respond. Make sure the remote control is aimed at your home entertainment device and is not farther than 15 feet away. The unit does not control home entertainment devices or commands are not working properly. Some combo units may require both a TV code and a VCR code for full operation. If original remote control required pressing ENTER to change channels, press ENTER on the remote control after entering the channel number. Tried "Search Method" and still could not find a working code. [. . . ] Suite 1000 Louisville, KY 40299 USA together with the original receipt and $3. 95 to cover postage and handling. The manufacturer reserves the right to substitute a currently manufactured model with equal or superior features. PROBLEM: SOLUTION: PROBLEM: SOLUTION: Due to RCA design (1983-1987), only the original remote control will operate these functions. If the above does not work. Please contact us in any of the following ways: PROBLEM: SOLUTION: · Please visit : www. oneforall. com · If the above website is not able to provide you with the information you need, please email us at ofasupport@ueic. com · Customer Support : (330) 405-8612 9 10 CTGRD4N 4110 manual booklet. QXD 5/2/06 3:09 PM Page 11 ADDITIONAL INFORMATION As you update your home entertainment system, One For All® has a universal remote control that will fit your needs. Look for these exciting products at a retailer near you. One For All Access 3 . [. . . ]