User manual UNIVERSAL REMOTE CONTROL ONE FOR ALL URC4220

[. . . ] For master power control, see Programming A Master Power Macro on page 10. Use the keypad (1 ~ 9 and 0) to directly select channels (e. g. , 009 or 031). Use REW, PLAY, FWD, PAUSE, or STOP to control your VCR, PVR (or DVR), or DVD player. For a VCR, PVR (or DVR), or VOD (if available), use SCANor SCAN+ to quickly scan forward or back through a video program. Use QUICK SKIP to advance the video program a preset amount (as set on your device). Press REC twice to record a VCR or PVR (or DVR) program. Use SLEEP to set the sleep timer on a selected device if equipped with this feature. Use SET for all programming sequences. Use TV/VID to switch the TV's input to view TV or video programs. [. . . ] This action is normal. continued on next page. . . 4. To view the code for the first digit, press 1 once. Wait 3 seconds, count the LED blinks (e. g. , three blinks = 3) and write down the number in the leftmost box in the TV code boxes on page 8. NOTE: If a code digit is "0", the LED will not blink. 9 10 WALRB4P manual booklet 5/2/06 3:16 PM Page 11 PROGRAMMING A MASTER POWER MACRO (continued) Clearing The Master Power Macro 1. Press and hold SET until the LED (red light) blinks twice, then release SET. Then press POWER once. 2. Press FAV once. · If Favorite Channel Scan has been set up, scanning of favorite channels will start with up to 100 channel changes or until stopped by pressing any key. · If Favorite Channel Scan has not been set up, scanning will start with the current channel, and continue up to 100 channel changes or until stopped by pressing any key. 3. To stop scanning channels at any time, press any key once. PROGRAMMING FAVORITE CHANNEL SCAN 3. In the CBL/SAT or TV mode, you can store a list of up to 10 favorite channels, in any order, that will be immediately scanned when FAV is pressed (see Using Channel Scan on the previous page). NOTE: Favorite channels can only be programmed for one mode. After programming, if FAV is pressed while in another mode, the remote control will start scanning all channels instead (if applicable to the selected device). RE-ASSIGNING DEVICE KEYS The One For All 4 Device Universal Remote Control can be set to control a second PVR, VCR, or DVD player. For example, to control a TV, a cable box, and two DVD players, re-assign the unused VCR/PVR key to operate the second DVD player as follows: 1. On the remote control, press and hold SET until the LED (red light) blinks twice, then release SET. The LED will blink twice. 1. On the remote control, press CBL/SAT or TV once. 2. 3. Press and hold SET until the LED (red light) blinks twice, then release SET. The VCR/PVR key is now ready to be set up to control your second DVD player. See Programming Device Control on page 8. 4. Use the keypad to enter a favorite channel number (e. g. , 031). Then press SET once. NOTE: If the original remote control required pressing an Enter key to change the channel, also press the ENTER key after the channel number (e. g. , 0 - 3 - 1 - ENTER). On some satellite receivers and cable boxes, you may need to press the SELECT (OK) key instead of ENTER. To re-assign a second VCR or PVR (or DVR) to the unused DVD key, repeat steps 1 through 4 . However, in step 3 substitute VCR/PVR for DVD, and in step 4 substitute DVD for VCR/PVR. Now the DVD key will be ready to be set up as your second VCR or PVR (or DVR). See Programming Device Control on page 8. NOTE: Only one device can be assigned to an unused device key at a time. 5. If desired, repeat step 4 for each channel to be stored, up to a total of 10 channels. NOTE: If you try entering more than 10 channels, the remote control will automatically exit programming. To change your favorite channel list at this point, you will first need to delete the existing list by performing the steps in "Clearing Custom Programming"on page 14. Then, perform the instructions in this section once again. USING CHANNEL SCAN In the CBL/SAT or TV mode, use the FAV key to start a 3-second scan of all channels. Or, if programmed, use the FAV key to scan only your favorite channels to view a desired channel (see Programming Favorite Channel Scan on next page. Press CBL/SAT or TV once. 6. To exit programming with less than 10 favorite channels stored, press and hold SET until the LED blinks twice. Otherwise, the remote control will automatically exit the program after 10 channels have been stored. 11 12 WALRB4P manual booklet 5/2/06 3:16 PM Page 13 CHANGING VOLUME LOCK The One For All 4 Device Universal Remote Control is set at the factory for independent volume control of each selected device. However, you may change the Volume Lock setting to Global Volume Lock so that a device's volume will be locked to one mode (e. g. , to control TV volume in all other modes). After that, if desired, you can perform Individual Volume Unlock on a selected device to set its volume control for independent operation. 3. Volume will again be independently controlled according to its default states for all programmed devices. Locking Volume Control To One Mode (Global Volume Lock) 1. [. . . ] This warranty does not cover damages or failures caused by products or services not supplied by OFA, or which result from accident, misuses, abuse, neglect, mishandling, misapplication, faulty installation, set-up adjustment, improper maintenance, alteration, maladjustment of consumer controls, modifications, commercial use, or that is attributable to acts of God. OFA SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF WARRANTY, ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation of incidental or consequential damagers, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. [. . . ]