User manual UNIVERSAL REMOTE CONTROL S4000

[. . . ] Generic Pioneer Charter OCAP. fm Page 1 Friday, July 20, 2007 1:28 PM C4000 and S4000 Universal Remote Controls Users Guide PREPROGRAMMED FOR YOUR SET-TOP BOX Generic Pioneer Charter OCAP. fm Page 2 Friday, July 20, 2007 1:28 PM TABLE OF CONTENTS Introduction . 15 Unlocking Volume Control for a Single Device (Individual Volume Unlock) . 16 Locking Volume Control To One Mode (Global Volume Lock) 17 Programming Cable ID Lock . 41 M1060A www. urcsupport. com 2 7/20/07 Generic Pioneer Charter OCAP. fm Page 3 Friday, July 20, 2007 1:28 PM INTRODUCTION The C4000 and S4000 Remote Controls by Universal Electronics are our latest generation universal remote controls. [. . . ] To search for the codes of your other devices, repeat steps 1 through 5, but substitute the appropriate key (e. g. , AUX, DVD, CBL, or STB) for the device you are searching for. 7. CHECKING THE CODES If you have set up the C4000 and S4000 Remote Controls by searching for your device code (on the previous page), you may need to find out which five-digit code is operating your equipment. www. urcsupport. com 13 Generic Pioneer Charter OCAP. fm Page 14 Friday, July 20, 2007 1:28 PM For example, to find out which code is operating your TV: 1. The TV key blinks twice. 3. NOTE: 4. To view the code for the first digit, press 1 once. Count the number of times the TV key blinks (e. g. , 3 blinks = 3) and write down the number in the leftmost TV Code box on page 11. Use 2 for the second digit, 3 for the third digit, 4 for the fourth digit, and 5 for the fifth digit. To check for other device codes, repeat steps 1 through 4, but substitute the appropriate key (e. g. , AUX, DVD, CBL, or STB) for the device you are checking. Write down the codes in the appropriate boxes on page 11. 5. www. urcsupport. com 14 Generic Pioneer Charter OCAP. fm Page 15 Friday, July 20, 2007 1:28 PM PROGRAMMING CHANNEL CONTROL LOCK By default, the remote control's channel-control capabilities are locked to the cable converter. This guarantees that you do not inadvertently change a channel on your TV or VCR. However, you can deactivate this feature to allow full access to these keys in the TV and VCR modes. The CBL (or STB) key blinks four times. Now the remote control provides TV and VCR channelcontrol capabilities while in the TV or VCR mode. Enter 9 7 3. The CBL (or STB) key blinks twice. 3. Press CH+ once. The CBL (or STB) key blinks twice. Now, regardless of what mode you select, the channel keys only change channels on your cable converter. CHANGING VOLUME LOCK Volume Lock allows you to control the volume through the device identified as having your primary speaker(s), regardless of which mode you are using. On the C4000 and S4000 Remote Controls, Global Volume Lock is set to TV, so you can control TV volume while in the AUX, www. urcsupport. com 15 Generic Pioneer Charter OCAP. fm Page 16 Friday, July 20, 2007 1:28 PM DVD, TV or CBL mode. You can perform Individual Volume Unlock on a selected device to set its volume control for independent operation. Unlocking Volume Control for a Single Device (Individual Volume Unlock) 1. Assuming Global Volume Lock is active, select a mode on the remote control that you want to unlock (e. g. , CBL) and press it once. The last-selected device key blinks four times. 4. Repeat steps 1 through 3 for each device you want volume to be unlocked. Now, after you select a device that has volume unlocked (e. g. , CBL), pressing VOL+, VOL-, or MUTE, controls only that device's volume. Unlocking All Volume Control (Global Volume Unlock) NOTE: Performing these instructions sets independent volume control for all programmed devices. On the remote control, press and hold SET UP until the last-selected device key blinks twice. The last-selected device key blinks four times. www. urcsupport. com 16 Generic Pioneer Charter OCAP. fm Page 17 Friday, July 20, 2007 1:28 PM Locking Volume Control To One Mode (Global Volume Lock) 1. On the remote control, press and hold SET UP until the last-selected device key blinks twice. The last-selected device key blinks twice. 3. Select a mode (e. g. , TV or AUX) which you want to use to control the volume. [. . . ] SOLUTION: Replace the batteries with two (2) new AA batteries (see "Installing Batteries" on page 9). PROBLEM: Device key blinks when you press a key, but home entertainment device does not respond. SOLUTION: Make sure you are aiming the remote control at your home entertainment device and that you are within 15 feet of the device you are trying to control. PROBLEM: The remote control does not control home entertainment devices or commands are not performing properly. [. . . ]