User manual UNIVERSAL REMOTE CONTROL STAR LIGHT

[. . . ] 13 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Warranty and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Three Digit Code Lists . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 30 A. Aux Codes Satellite Functions by code. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Step 2: On the Star Light universal remote control, press the corresponding DEVICE button (TV, VCR, CATV, SAT, Audio, or Aux) and the MUTE button simultaneously. Note: SET will appear in the LCD. Step 3: Locate the three digit code number for your brand of equipment from the code lists found on pp. Note: If the brand list contains more than one code number, select the first code listed. Step 4: Point the remote control at the devise turned on in Step1 and press in the three digit code number selected in Step 3. If the device fails to turn off, go back to Step 3 and select the next three digit code for your equipment, and press in the code number. Step 5: Press the DEVICE button (TV, VCR, CATV, SAT, Audio, Aux) on the remote control to store the three digit code that turned off your equipment. Note: PASS will flash in the LCD indicating that the code has been stored. If any of the buttons do not perform as they should, please repeat from Step 2 using the next three digit code until the right code is found. Step 7: To program other devices into the corresponding Device button of the remote control, repeat the above steps with the respective devices and Device buttons. 7 Advanced Features A. Three Digit Code Number Recall: If you wish to find a code number that has been stored in your remote control, please use the following steps: Step 1: On the remote control, press the DEVICE and MUTE buttons simultaneously. The LCD will flash the three digit code number for five seconds before returning to its original sate. B. Storing Multi-Commands/Favorite Channels to Memory Buttons Memory buttons M1, M2, M3 and M4 can be set up to store up to six(6) commands with one button push. Any functions, in any Device mode (except Channel up and Channel down), can be stored in any one of the four memory buttons. This will enable you, for example, to turn on the TV and Satellite receiver and select a preassinged satellite channel with only one button push. Method of setting up: Step 1: Press the Device button (TV, VCR, CATV, SAT, AUX, AUDIO) and MUTE button, simultaneously. Step 2: Press one of the memory buttons(M1-M4) that you would like to designate for multi-command or favorite channel operation. Step 3: Press up to six commands that you would like to store in the memory button. Note: SAVE will flash twice and the Device mode will appear in the LCD. Please repeat the above steps for the remaining memory buttons. 8 Example: Memory button M1 in the SAT mode can be set up to do the following functions: to turn on the Satellite receiver, select channel #18 on the satellite receiver, and then turn on the TV. Press the # 1 button (to select the first digit of channel # 18) Note: M 1 2 will appear in the LCD. Press the # 8 button (to select the second digit of channel # 18) Note: M 1 3 will appear in the LCD. Now, anytime the memory button M1 is pressed while the remote control is in the SAT mode, the commands to turn on the Satellite receiver, select the Satellite channel #18 and turn on the TV, will be sent out by the remote control. Note: Any previously stored multi-commands on a memory button will be erased when new multi-commands are stored to that same memory button. 9 Advanced Features ( Continued ) C. [. . . ] TV volume will now operate in the SAT mode. To return to the original volume control setting. Step 1: Press the DEVICE button(VCR, CATV, SAT, etc. ) and MUTE button, simultaneously. The TV volume Punch Through for the selected device mode is now deactivated. 11 Advanced Features ( Continued ) E. Punch Through VCR Controls. After setting up the remote control to work your respective TV, VCR, CATV, Satellite equipment, etc, the remote control can also be set up so that the VCR control buttons (PLAY, STOP, FAST FORWARD, REWIND, PAUSE, and RECORD) will operate (VCR controls), even when the remote is in a different Device mode. [. . . ]